The wholesaler for smart home professionals
Shipping within 24h
B2B portal
Direct delivery from stock
Technical support

SONOFF ZBMINI-L2 Zigbee Smart Switch (No Neutral)

Compact SONOFF Zigbee 3.0 in-wall module for one lighting circuit up to 6 A, no neutral wire needed, controlled via gateway and existing switch.
Product number: ZBMINIL2
Manufacturer: SONOFF
EAN: 6920075772111
Manufacturer product ID: ZBMINIL2
Product information "SONOFF ZBMINI-L2 Zigbee Smart Switch (No Neutral)"

The SONOFF ZBMINI-L2 (ZBMINIL2) is a compact Zigbee 3.0 in-wall module for one lighting circuit that works without a neutral wire. It is fitted behind an existing switch in the back box and connects with L-in and L-out, so older installations with a live wire only can be made smart.

Control is via a Zigbee gateway (remote, schedules, scenes) and locally via an existing wall switch or push button on terminals S1/S2, including two-way staircase wiring. The module switches up to 6 A at 100–240 V AC. For LED lighting the maximum is 300 W at 230 V, with a minimum load of 3 W and no separate anti-flicker module required. It is a Zigbee end device and therefore not a router: it does not extend the Zigbee network.

Specifications

  • Model: ZBMINIL2
  • Application: Light switching without neutral wire
  • Supply: 100–240 V AC, 50/60 Hz
  • Load: 6 A max.; LED 300 W max. at 230 V, 3 W minimum
  • Protocol: Zigbee 3.0, end device (not a router)
  • Control: Zigbee gateway plus wall switch or push button on S1/S2
  • Mounting: in-wall, suitable for EU/86/120 boxes
  • Dimensions: 39.5 × 32 × 18.4 mm
  • Operating temperature: −10 … 40 °C

Have the mains installation carried out by a qualified installer, with a 6 A circuit breaker or RCBO upstream of the module. Do not connect an anti-flicker module or inductive loads such as fans. A Zigbee 3.0 gateway is required.

Properties
Actors: Switch
Installation method: Flush mount
Matter: No
Power source: 100-240V AC, 50/60Hz
Protocol: Zigbee 3.0
Downloads "SONOFF ZBMINI-L2 Zigbee Smart Switch (No Neutral)"
New
SONOFF SNZB-01P Zigbee Wireless Switch (incl. battery)
The SONOFF SNZB-01P is a compact wireless Zigbee 3.0 button. For each press type you set separate actions for a single, double and long press, so one button can switch several devices or scenes. The button works with Zigbee 3.0 gateways such as the SONOFF NSPanel Pro, ZB Bridge Pro and ZBDongle-E and with most other gateways that follow Zigbee 3.0. You can also use it as an emergency button that sends a notification to housemates’ phones, or as a trigger for an Alexa routine (with an Alexa Zigbee hub). It is intended for two-way light switching, a doorbell or a coffee-machine button, among other uses. For more scenes on one controller there is the four-button SNZB-01M. Specifications Model: SNZB-01P Application: Wireless Zigbee button with single, double and long press Protocol: Zigbee 3.0 (IEEE 802.15.4) Battery: CR2477 (3 V), up to 5 years according to the manufacturer (lab test) Mounting: adhesive or screw, indoor Dimensions: 45 × 45 × 17.7 mm; 27.7 g Operating temperature: −10 … 60 °C A Zigbee gateway is required. The button is suitable for indoor mounting.
Product number: SNZB-01P

€13.97*
New
SONOFF MINI-D Matter Over Wi-Fi Dry Contact Switch
The SONOFF MINI-D is a Wi-Fi switch with a dry contact and Matter support. It controls equipment that only expects a dry contact signal, such as a garage door opener, a boiler or a gate, and can be powered either from the mains (100–240 V AC) or from 12–48 V DC. The output is a dry contact in NO or NC configuration and is suitable for direct current only: 24 V DC at 2 A resistive load or a 12/24 V DC motor up to 8 W. Alternating-current loads must not be connected to the output. For higher power, switch a contactor. Via Matter, on/off control, voice control and scenes are available in platforms such as Apple Home, Google Home, Alexa and Home Assistant. With the eWeLink app no separate hub is needed. Specifications Model: MINI-D Application: Dry contact for e.g. garage door, boiler or DC motor Supply: 100–240 V AC (0.1 A max.) or 12–48 V DC (1 A max.) Load: DC output only: 24 V DC / 2 A resistive load or 12/24 V DC motor up to 8 W Protocol: Matter over Wi-Fi (2.4 GHz, IEEE 802.11 b/g/n) Control: eWeLink app or Matter platform (on/off) Dimensions: 41 × 43 × 21.5 mm; 34.5 g Operating temperature: −10 … 40 °C Have the mains installation carried out by a qualified installer. Never connect the AC and DC supply at the same time and do not connect an AC load to the output. A Matter controller is required to link to Matter platforms.
Product number: MINI-D

€12.31*
New
SONOFF Zigbee Water Leak Sensor with WLDC200 cable
The SONOFF SNZB-05PC is the set of the SNZB-05P Zigbee water leak sensor with the 2-metre WLDC200 water leak detection cable. The cable registers water along a line rather than at a single point, which is useful behind a boiler, under a washing machine or along a pipe. Several WLDC200 cables can be connected in series with no length limit, and a wet cable can be reused after it has dried completely. A recommended ambient humidity is 0–80 % RH without condensation; very humid rooms can be mistaken for water. On detection the sensor sends a push notification and, via a scene, can start an alarm on the gateway, even without Wi-Fi. The sensor is IP67 and works with Zigbee 3.0 hubs such as NSPanel Pro, iHost and the ZB Bridge variants. Without the cable the SNZB-05P is available. Specifications Model: SNZB-05PC Application: Zigbee water leak sensor Protocol: Zigbee 3.0 (IEEE 802.15.4) Ingress protection: IP67 Set: SNZB-05P sensor + 2 m WLDC200 water leak detection cable Battery: CR2477 (3 V), up to 5 years at 50 triggers per day according to the manufacturer Dimensions: 48 × 48 × 21.6 mm; 34.3 g (without battery) A Zigbee gateway is required. For indoor use only.
Product number: SNZB-05PC

€18.93*
New
SONOFF NSPanel Pro Gen2 White
The SONOFF NSPanel86PW-Relay (NSPanel Pro Gen2, white version) is an 86 × 86 mm control panel with a 3.95-inch touchscreen and two built-in relays. It replaces an existing wall switch and switches one or two lighting groups, up to 5 A per channel and 10 A in total for a resistive load. The panel is a Zigbee 3.0 hub, a Matter hub and a Matter bridge at the same time, so Zigbee and Wi-Fi devices become available in a Matter environment. According to SONOFF its processing power (quad-core Cortex-A35, 2 GB RAM, 32 GB storage) runs several third-party apps, including Home Assistant through F-Droid, without root access. It also offers a thermostat function, energy monitoring, two digital microphones, a 1.5 W speaker, a light sensor and dual-band Wi-Fi (2.4 and 5 GHz). The only difference from the NSPanel86PB-Relay is the colour: this model is white, the NSPanel86PB-Relay is dim gray. Specifications Model: NSPanel86PW-Relay (NSPanel Pro Gen2, wit, 86 mm) Application: Central control panel with two relays replacing an existing wall switch Supply: 100–240 V AC, 50/60 Hz Load: 2 channels, 5 A max. per channel and 10 A total (resistive load) Display: 3.95-inch capacitive touchscreen, 480 × 480 Protocol: Wi-Fi IEEE 802.11 b/g/n/ac/ax 2.4 GHz and 5 GHz; Zigbee 3.0 Gateway: built-in Zigbee hub (EFR32MG24), Matter hub and Matter bridge Chip: quad-core ARM Cortex-A35 (RK3326-S), 2 GB RAM, 32 GB storage Colour: white Housing: PC + CRS Dimensions: 86 × 86 × 39.5 mm; 190 g Operating temperature: -10 … 40 °C, 10–80 % RH non-condensing Have the mains connection carried out by a qualified installer, with the correct upstream protection in the consumer unit. Update the firmware over the air for the latest features.
Product number: NSPanel86PW-Relay

€123.88*
New
SONOFF TRV Gen2 Zigbee Thermostatic Radiator Valve
The SONOFF TRV-ZBT (TRV Gen2) is a Zigbee thermostatic radiator valve with a rotatable IPS colour display. Compared with the TRVZB its volume is 38 % smaller, which helps in tight spaces and complex piping, and the valve movement is low-noise. The valve fits existing M30 × 1.5 mm valves and the supplied adapters fit most heating manufacturers. There are three independent heating plans with a combined maximum of 12 temperature periods. Energy saving comes from open-window detection (temperature drop or linkage with a door/window sensor), an energy-saving mode and linkage with a motion sensor. An external SONOFF temperature sensor from the SNZB-02 series can serve as the measuring point for room temperature. Protections are child lock, anti-calcification, anti-freeze and a low-battery warning. Group control, boost mode and temperature offset are also available, and the history of target temperature, current temperature and heating activity goes back six months. Zigbee2MQTT needs version 2.12.1 or later; via ZHA a script is needed for the full function set. Specifications Model: TRV-ZBT (TRV Gen2) Application: Zigbee thermostatic radiator valve with IPS colour display Thread: M30 × 1.5 mm Supply: 2 × AA (LR6, 1.5 V alkaline) Range: setting range 5 … 30 °C Protocol: Zigbee 3.0 (IEEE 802.15.4) Dimensions: 50 × 50 × 82.9 mm; 169 g (with batteries) Operating temperature: −10 … 50 °C Before installation, check valve compatibility in the manufacturer’s compatibility guide. A Zigbee gateway is required.
Product number: TRV-ZBT

€28.84*
New
SONOFF Zigbee Motion Sensor
The SONOFF SNZB-03P is a Zigbee 3.0 motion sensor using passive infrared technology. It detects moving people within 6 metres and an angle of 110° and switches lights, cameras or alarms via scenes. Detection responds within roughly 5 seconds. Scenes can react to motion, no motion, or no motion for a set time, and also to ambient light level (bright or dim), so that lighting switches on only in the dark. Because the scenes run locally within the Zigbee network, they also work without an internet connection as long as the devices have power. Do not place the sensor in direct sunlight or near heat sources, which can disturb the infrared detection. For detecting people who are sitting still, the radar-based SNZB-06P is the suitable choice. Specifications Model: SNZB-03P Application: Zigbee motion sensor (passive infrared) Protocol: Zigbee 3.0 (IEEE 802.15.4) Range: detection angle 110°, detection distance 6 m Battery: CR2477 (3 V), over 3 years according to the manufacturer Dimensions: 44 × 44 × 65 mm; 54 g Operating temperature: −10 … 60 °C A Zigbee gateway is required. For indoor use only.
Product number: SNZB-03P

€13.64*
New
SONOFF IP65 Zigbee LCD Smart Thermometer (Probe Version)
The SONOFF SNZB-02LD is a Zigbee 3.0 thermometer with a 1.5 m external probe for measuring temperature in liquids and enclosed spaces. The value is shown on a 2.2-inch LCD, and the housing has ingress protection IP65. The probe measures from −40 to 115 °C, the housing operates from −10 to 60 °C. Through a Zigbee hub and the eWeLink app the temperature history can be viewed and exported by day, by month or up to six months back (storage of up to 180 days); alerts for abnormal temperatures and automations based on temperature can be set up. Typical applications are water tanks, refrigerators, pipes and aquariums. IP65 covers splashing water: do not submerge the device or expose it to high-pressure jets or rain. Specifications Model: SNZB-02LD Application: Temperature measurement in liquids and enclosed spaces with an external probe Protocol: Zigbee 3.0 Display: 2.2-inch LCD Ingress protection: IP65 (splash-proof) Operating temperature: housing -10 … 60 °C; probe -40 … 115 °C Battery: CR2477, included Dimensions: 62.8 × 58.5 × 21.8 mm; probe cable 1.5 m; 86.2 g incl. cable Contents: thermometer, quick guide, Velcro strip, card pin, hanging cord A Zigbee 3.0 hub (for example SONOFF iHost, NSPanel Pro, ZBBridge-P, ZBBridge-U or a ZBDongle) is required. Update the hub to the latest firmware before adding the device.
Product number: SNZB-02LD

€16.45*
New
SONOFF Dongle Max Zigbee/Thread PoE Dongle
The SONOFF Dongle-M (Dongle Max) is a Zigbee/Thread dongle based on EFR32MG24 and ESP32 that connects Zigbee devices to open-source platforms such as Home Assistant and Zigbee2MQTT. It works over Ethernet with PoE, over Wi-Fi or over USB-C, so its location is not tied to a USB port on the server. Through the local web console on the network, status, settings and logs can be viewed and the firmware can be switched or updated without disassembly or manual flashing: as Zigbee coordinator, Zigbee router or Thread RCP. Webhooks for backups and alerts when the network drops, MQTT for Home Assistant and remote access via WireGuard VPN are also available. The dongle works with USB and TCP connections and has two adjustable 5 dBi antennas for 360° coverage. The housing is made of aluminium (tested by SONOFF in a 24-hour salt spray test) and the product is CE, FCC and RoHS certified. Specifications Model: Dongle-M (Dongle Max) Application: Zigbee coordinator, router or Thread radio for open-source platforms, via Ethernet (PoE), Wi-Fi or USB Chip: EFR32MG24 + ESP32 Protocol: Zigbee 3.0; Wi-Fi IEEE 802.11 b/g/n 2.4 GHz; Ethernet (RJ45) Supply: 5 V 1 A via USB-C or 48 V 0.25 A via PoE port Control: local web console: status, settings, logs, firmware switching and updates; webhooks, MQTT and VPN (WireGuard) Range: two adjustable 5 dBi antennas Housing: aluminium and PC+ABS, dim gray Operating temperature: -10 … 60 °C Contents: dongle, USB-C to USB cable, quick guide A Zigbee network has one coordinator; use a single integration (ZHA or Zigbee2MQTT) per dongle. If the web console cannot be reached via Dongle-M.local, use the IP address.
Product number: Dongle-M

€35.45*
New
SONOFF DUALR3 2-Gang Wi-Fi Smart Switch
The SONOFF DUALR3 is a Wi-Fi in-wall module with two independent relays and power metering per channel. In switch mode it controls two separate loads, in motor mode a roller-shutter, curtain or sun-blind motor, and in meter mode it acts as a stand-alone meter. For each channel the module measures voltage, current and power, and with the overload protection in the eWeLink app you set thresholds at which the channel switches off. Each channel switches up to 10 A, with 15 A in total; in motor mode the load is 1 A. Two inputs take external switches (rocker, momentary or SPDT), so the wall control is retained. No separate gateway is needed and there is local LAN control. Specifications Model: DUALR3 Application: Two-load switching or shutter motor control, with power metering Supply: 100–240 V AC, 50/60 Hz Load: 10 A per channel, 15 A total; motor load 1 A Protocol: Wi-Fi 2.4 GHz (IEEE 802.11 b/g/n) Control: eWeLink app, LAN control, two external switch inputs Mounting: in-wall Dimensions: 54 × 49 × 24 mm Operating temperature: −10 … 40 °C Have the mains installation carried out by a qualified installer, with upstream protection matching the load. Select the working mode in the eWeLink app before commissioning; in motor mode the motor determines the maximum load.
Product number: DUALR3

€12.31*
New
SONOFF Zigbee Temperature and Humidity Sensor
The SONOFF SNZB-02P is a compact Zigbee 3.0 temperature and humidity sensor without a display. Stick or place it where you need it and follow the values via a Zigbee gateway in the eWeLink app or in your own system. The sensor, with a Swiss hygrometer chip, measures accurately to ±0.2 °C and ±2 % RH and refreshes every 5 seconds. You receive a notification as soon as a set comfort threshold is exceeded, and you can view and export six months of history by day, month or half-year. It works with Zigbee 3.0 hubs such as SONOFF iHost, NSPanel Pro, ZB Bridge Pro and ZBDongle-E, and with third-party hubs such as Echo 4th Gen and SmartThings Hub V3. If you want to read the values on the device itself, choose the SNZB-02D with LCD display. Specifications Model: SNZB-02P Application: Compact Zigbee temperature and humidity sensor Protocol: Zigbee 3.0 (IEEE 802.15.4) Accuracy: ±0.2 °C and ±2 % RH Range: −10 … 60 °C; 5–95 % RH, non-condensing Battery: CR2477 (3 V), up to 4 years according to the manufacturer (lab test) Dimensions: 45 × 45 × 17.7 mm; 26.7 g A Zigbee gateway is required. For indoor use only.
Product number: SNZB-02P

€13.97*
New
SONOFF MINI-RBS Smart Roller Shutter Switch
The SONOFF MINI-RBS is a compact Wi-Fi switch for roller shutter, screen and awning motors. It drives a motor of up to 1 A (100–240 W), fits, according to SONOFF, in small flush-mounting boxes including the European 60 mm boxes, and is Matter compatible. The position can be set in percent and the travel time can be calibrated to compensate for motor deviations. Schedules for opening and closing can be set in the eWeLink app; through Matter (a Matter hub is required) the device can be added to platforms such as Alexa, Apple Home and Google Home. Connecting an external switch (S1/S2) is not mandatory: the app and automations also work without one. If the switching behaviour does not match the switch type, the switch mode can be changed by pressing the button briefly three times. The motor must not run in the same direction for more than 2 minutes; the device then stops automatically. Specifications Model: MINI-RBS Application: Controlling a roller shutter, screen or awning motor Supply: 100–240 V AC, 50/60 Hz Load: motor 100–240 W / 1 A max. Protocol: Wi-Fi IEEE 802.11 b/g/n 2.4 GHz; Matter compatible Control: eWeLink app or Matter platform: percentage position, schedules, travel calibration Mounting: flush mounting, including European boxes (Ø 60 mm) Housing: PC Operating temperature: -10 … 40 °C Have the mains installation carried out by a qualified installer, with a suitable circuit breaker in the consumer unit. Refer to the manual for the wiring diagram.
Product number: MINI-RBS

€13.97*
New
SONOFF Zigbee 3.0 USB Dongle Plus
The SONOFF ZBDongle-E (Zigbee 3.0 USB Dongle Plus) is a USB stick that acts as a Zigbee coordinator for local smart-home systems. It comes pre-flashed with EZNet coordinator firmware (6.10.3) and is ready to use with Home Assistant, openHAB and Zigbee2MQTT. The stick is built around the EFR32MG21 chip with +20 dBm output power and has a shielded aluminium housing that limits interference from surrounding equipment. With the Dongle Flasher web tool the firmware can be switched in about a minute, for instance to router firmware to extend Zigbee range. A USB extension cable between port and stick is recommended to limit interference. Green Power devices are supported; for Hue Green Power the channel must be set to 11, 15, 20 or 25. The difference from the ZBDongle-P lies in the chip and the supported platform: the ZBDongle-P uses a CC2652P. Specifications Model: ZBDongle-E (Zigbee 3.0 USB Dongle Plus) Application: USB Zigbee coordinator for Home Assistant, openHAB and Zigbee2MQTT Chip: EFR32MG21, +20 dBm Firmware: EZNet 6.10.3 Supply: DC 5 V (100 mA max.) Housing: aluminium alloy Dimensions: 75 × 25.5 × 13.5 mm Operating temperature: −10 … 40 °C A host with a USB port and a Zigbee platform such as Home Assistant is required. One stick can be used per ZHA installation.
Product number: ZBDongle-E

€20.58*
New
SONOFF MINI-DIM-E Smart Dimmer Switch
The SONOFF MINI-DIM-E (Orb-DIM from the Fusion series) is a Matter-over-Wi-Fi dimmer in the form of a complete 86 × 86 mm wall switch. Unlike the MINI-DIM in-wall module, this version replaces the existing wall control and has its own control front. The dimmer controls dimmable LED lamps, incandescent and halogen lamps and dimmable electronic transformers in 1 % steps. Dimming uses trailing edge and leading edge; the leading-edge mode is intended only for older fixtures under 100 W, such as incandescent and halogen lamps. Automatic and manual calibration match the dimming range to the lamp, which limits flicker and stepped dimming. The load rating is 400 W resistive or 200 VA LED. Protection against overload, overcurrent and overheating switches off on a fault. Not suitable for fluorescent tubes, CFLs, LED strips or inductive loads such as motors and fans. Specifications Model: MINI-DIM-E (Orb-DIM, Fusion) Application: Dimming dimmable LED, incandescent and halogen lamps Supply: 220–240 V AC, 50 Hz, neutral wire required Load: resistive load 400 W max.; LED 200 VA Protocol: Matter over Wi-Fi (2.4 GHz, IEEE 802.11 b/g/n) Features: power monitoring, 1 % steps, automatic and manual calibration Protection: overload, overcurrent and overheat Mounting: wall switch, 86 × 86 mm Dimensions: 86 × 86 × 33.7 mm; 83 g Operating temperature: −10 … 40 °C The dimmer works on 220–240 V AC only and requires a neutral wire. Have the mains installation carried out by a qualified installer. A Matter controller is required to link with Matter platforms.
Product number: MINI-DIM-E

€24.71*
New
SONOFF SenseGuard DW Gen2 Zigbee Door/Window Sensor
The SONOFF SNZB-04PR2 (SenseGuard DW Gen2) is a Zigbee door and window sensor with tamper protection. The sensor registers opening and closing from the distance between transmitter and magnet and reports it via the app or in scenes. The transmitter is only 14 mm thick and the magnet 6.5 mm. The magnet can be mounted horizontally or vertically and detached from the housing so that the sensor also fits in tight spots. Mounted horizontally, the detection distance is up to 30 mm, suitable for older doors and windows with a wider gap. A tamper switch on the back reports immediately when the sensor is removed; that status can also be used as a trigger. Open or closed for a set time can serve as a condition, for instance to switch off a thermostat when a window is open. The sensor runs on AAA batteries and is therefore easy to replace. Specifications Model: SNZB-04PR2 (SenseGuard DW Gen2) Application: Zigbee door/window sensor with tamper protection Protocol: Zigbee (IEEE 802.15.4) Battery: 2 × AAA (LR03, 3 V), up to 3 years according to the manufacturer Range: magnet mounted horizontally: up to 30 mm detection distance Dimensions: transmitter 90 × 26 × 13.5 mm; magnet 31 × 14 × 6.5 mm; 45.1 g incl. batteries Operating temperature: −10 … 60 °C A Zigbee gateway is required. For indoor use only.
Product number: SNZB-04PR2

€11.49*
New
SONOFF MINI-ZBRBS-E Zigbee Roller Shutter Switch
The SONOFF MINI-ZBRBS-E (Orb-ZBRBS from the Fusion series) is a Zigbee 3.0 roller-shutter switch in the form of a complete 86 × 86 mm wall switch. It controls one roller-shutter, screen or awning motor up to 1 A and replaces the existing wall control, rather than sitting as a separate module behind the switch like the MINI-ZBRBS. Via a Zigbee gateway you set the position as a percentage, create schedules and scenes and reverse the direction of rotation without rewiring. The switch also works as a Zigbee router and so strengthens the mesh. Two limitations apply: the motor must not run in the same direction for more than 2 minutes at a time (the device then stops automatically) and several motors in parallel on one switch are not supported. If automatic calibration fails, for instance with a very small motor, switch to manual calibration. Specifications Model: MINI-ZBRBS-E (Orb-ZBRBS, Fusion) Application: Controlling a roller shutter, screen or awning motor Supply: 100–240 V AC, 50/60 Hz, neutral wire required Load: motor 1 A max. Protocol: Zigbee 3.0, also a Zigbee router Control: Zigbee gateway: percentage position, schedules, direction reversal Mounting: wall switch for EU round boxes (Ø 60 mm) and 86-type boxes Dimensions: 86 × 86 × 34 mm; 84.1 g Operating temperature: −10 … 40 °C A neutral wire is required. Have the mains installation carried out by a qualified installer, with upstream protection matching the motor. A Zigbee 3.0 gateway is needed.
Product number: MINI-ZBRBS-E

€16.45*
New
SONOFF S61s Matter over Wi-Fi Smart Plug (Type F)
The SONOFF S61STPF (S61s) is a smart plug for Type F sockets with Matter over Wi-Fi and energy monitoring. It switches loads up to 16 A (3840 W maximum) at 100–240 V AC and measures voltage, current, power, runtime and energy use. According to SONOFF the measurement accuracy is ±1 % for voltage, ±2 % for current and ±3.5 % for power from 100 W (±3.5 W below 100 W); standby consumption is below 0.5 W. Through Matter the plug can be added to Apple Home, Google Home, Amazon Alexa, Home Assistant and SmartThings; pairing through the eWeLink app is also possible. With an electricity rate entered, usage and cost reports are generated, and schedules and scenes can be set. The housing is made of flame-retardant PC (V-0) and overload protection is configurable. Specifications Model: S61STPF (S61s, Type F) Application: Smart plug with energy monitoring Supply: 100–240 V AC, 50/60 Hz Load: 16 A max., 3840 W max.; standby < 0.5 W Accuracy: voltage ±1 %, current ±2 %, power ±3.5 % (≥ 100 W) or ±3.5 W (< 100 W) Protocol: Matter over Wi-Fi, IEEE 802.11 b/g/n 2.4 GHz Control: eWeLink app or Matter app, schedules and scenes Housing: PC, flame-retardant V-0, white Dimensions: 56 × 50 × 84 mm; 86 g Operating temperature: -10 … 40 °C, 5–95 % RH non-condensing According to SONOFF, do not connect a power strip to the plug, and stay below the maximum load of 16 A.
Product number: S61STPF

€8.26*
New
SONOFF ZBMINIR2 Extreme Zigbee Smart Switch (neutral required)
The SONOFF ZBMINIR2 (ZBMINI Extreme) is a compact Zigbee 3.0 in-wall module for one switching channel with a load of up to 10 A. Unlike the ZBMINIL2 this module needs a neutral wire, but in return it acts as a Zigbee router in the network. As a router the module supports up to 64 Zigbee end devices and so improves the coverage of the mesh. Local control remains possible with an existing wall switch (rocker, momentary or SPDT switch) or a door contact on S1/S2. With the ‘Detach Relay’ mode the external switch is decoupled from the relay, so smart bulbs stay online. The module switches a maximum of 10 A resistive load (2400 W at 240 V) and fits EU, 86 and 120 back boxes. Specifications Model: ZBMINIR2 Application: Switching lighting and small loads (neutral wire required) Supply: 100–240 V AC, 50/60 Hz Load: 10 A max. (resistive load 2400 W at 240 V) Protocol: Zigbee 3.0, also acts as a Zigbee router (up to 64 end devices) Control: Zigbee gateway plus wall switch (rocker, momentary, SPDT) Mounting: in-wall, suitable for EU/86/120 boxes Dimensions: 39.5 × 33 × 16.8 mm; 26.7 g Operating temperature: −10 … 40 °C Have the mains installation carried out by a qualified installer, with upstream protection matching the load. Live and neutral wires must be present in the back box; never connect S1 and S2 to neutral or earth. A Zigbee 3.0 gateway is required.
Product number: ZBMINIR2

€10.66*
New
SONOFF Zigbee Human Presence Sensor
The SONOFF SNZB-06P is a Zigbee 3.0 presence sensor with a 5.8 GHz microwave radar. Unlike an infrared detector it registers not only movement but also the breathing of people sitting still, so lights do not switch off while someone is still in the room. A built-in light sensor ensures that lighting only switches on in low ambient light. Sensitivity and detection duration are adjustable; the radial detection distance is approximately 4 metres. Because of its high sensitivity the sensor can trigger falsely, for example because of moving objects or several sensors aimed at each other. Install sensors in the same direction or back to back, at least 1.5 metres apart. Scenes with other Zigbee devices also run without internet. On an older ZB Bridge it is recognised only as a basic motion sensor, without the advanced settings. The sensor is powered via USB-C (5 V, 1 A) and so does not run on batteries; the SNZB-03P is intended for battery-powered motion detection. Specifications Model: SNZB-06P Application: Zigbee presence sensor with 5.8 GHz radar and light sensor Protocol: Zigbee 3.0 (IEEE 802.15.4) Supply: 5 V DC, 1 A via USB-C (power supply required) Range: radial detection distance approx. 4 m Dimensions: 44.2 × 44.2 × 59 mm; 31 g Operating temperature: −10 … 60 °C A Zigbee gateway and a USB-C power supply are required. For indoor use only.
Product number: SNZB-06P

€14.79*
New
SONOFF AirGuard TH Pressure Zigbee Temperature and Humidity Air Pressure Sensor
The SONOFF SNZB-02M (AirGuard TH Pressure) is a Zigbee 3.0 sensor that measures temperature, humidity and air pressure. In the eWeLink app it also calculates the dew point and VPD, so five quantities are available in one device. The accuracy is ±0.2 °C, ±2 % RH and ±0.1 hPa, with a refresh every 5 seconds. You set a comfort range for each of the three parameters; when exceeded, a notification follows in the app. The dew point is useful for spotting damp problems in walls early, the VPD for growing environments. Scenes can, for instance, switch a fan or dehumidifier, and six months of history can be viewed. The sensor is not waterproof and so is not intended for outdoor use. A change in air pressure gives general weather indications and is not a weather forecast. With the SNZB-02P you measure only temperature and humidity. Specifications Model: SNZB-02M (AirGuard TH Pressure) Application: Zigbee sensor for temperature, humidity and air pressure Protocol: Zigbee 3.0 (IEEE 802.15.4) Accuracy: ±0.2 °C, ±2 % RH, ±0.1 hPa Range: −20 … 60 °C; air pressure 700–1100 hPa Battery: CR2477 (3 V), included; over 2 years according to the manufacturer Dimensions: 45 × 45 × 17.6 mm; 27.3 g A Zigbee gateway is required. Home Assistant via ZHA needs a script. For indoor use only.
Product number: SNZB-02M

€16.45*
New
SONOFF Dongle Plus CC2674P10 Zigbee/Thread USB Dongle
The SONOFF Dongle-PP10 (Dongle Plus CC2674P10) is a Zigbee/Thread USB dongle based on the Texas Instruments CC2674P10. As delivered it works as a Zigbee coordinator for open-source platforms such as Home Assistant, Zigbee2MQTT and OTBR, so Zigbee devices are controlled locally, without the cloud. The chip has a 48 MHz Arm Cortex-M33 with 1024 KB flash and 256 KB RAM for larger networks with many devices communicating at the same time. With the SONOFF Dongle Flasher (web, Docker or Home Assistant add-on) the firmware can be switched in about a minute to Zigbee router or Thread RCP for Matter over Thread. The antenna provides 3 dBi by default and, according to SONOFF, can be optimised up to 4.5 dBi; the range is more than 200 m in free line of sight. The housing is made of aluminium alloy (tested by SONOFF in a 24-hour salt spray test) and the included 1 m USB extension cable limits interference from the USB port. Supported operating systems: Windows, Ubuntu, Raspberry Pi OS and Docker. Specifications Model: Dongle-PP10 (Dongle Plus CC2674P10) Application: Zigbee coordinator for open-source platforms; can also be flashed as Zigbee router or Thread radio Chip: Texas Instruments CC2674P10 (Arm Cortex-M33, 48 MHz, 1024 KB flash, 256 KB RAM); USB-serial CP2102(N) Protocol: Zigbee 3.0, IEEE 802.15.4, 2.4 GHz; Thread (OpenThread RCP) Range: up to 200 m in free line of sight; transmit power max. 20 dBm + 3 dBi antenna gain Supply: USB, 5 V 500 mA; standby 40 mW Firmware: coordinator firmware (Z-Stack) pre-installed; router firmware and Thread RCP can be flashed with the SONOFF Dongle Flasher Housing: aluminium alloy Dimensions: 18 × 10.5 × 214 mm Operating temperature: -10 … 60 °C, 0–95 % RH Contents: dongle, 1 m USB extension cable, quick guide A Zigbee network can have only one coordinator. Use one integration (ZHA or Zigbee2MQTT) per dongle.
Product number: Dongle-PP10

€29.67*
New
SONOFF Zigbee Smart Water Valve (EU)
The SONOFF SWV-BSP is a battery-powered Zigbee 3.0 water valve that is fitted between a tap and a hose. It is intended for automatic watering of lawns, borders, vegetable plots or potted plants, by time or by volume. The BSP version has a G3/4-14 thread and is intended for the United Kingdom, Europe and most regions. You choose between schedules and volume mode, each with single or cyclic irrigation, and you can see the water consumption and irrigation time for up to 180 days back. The built-in flow meter measures 2 to 39 L/min and adjusts the calculation for fluctuating water pressure. If the flow drops below 2 L/min, the valve recognises this as ‘no water’ and closes after 30 minutes. Vertical installation is recommended, as horizontal installation can increase the flow meter’s measurement error. Sealing tape and a rubber gasket are supplied for sealing. The valve works with Zigbee 3.0 hubs such as NSPanel Pro, iHost, ZB Bridge-P, ZB Bridge-U and ZBDongle-E/-P, and with Home Assistant. For North America there is the SWV-NH with a different thread. Specifications Model: SWV-BSP Application: Zigbee water valve for garden irrigation, between tap and hose Thread: G3/4-14 (BSP), 3/4" Supply: 4 × AA batteries (6 V), not included Protocol: Zigbee 3.0 Pressure and flow: working pressure 0.06–0.8 MPa; flow 2–39 L/min Ingress protection: IP55 Dimensions: 152 × 100 × 46 mm; 278 g Operating temperature: ambient 5 … 60 °C; water 5 … 40 °C Do not use in freezing conditions; the operating range is 5 to 60 °C. A Zigbee gateway is required. Four AA batteries are not supplied.
Product number: SWV-BSP

€24.71*
New
SONOFF ZBMINI-L2 Zigbee Smart Switch (No Neutral)
The SONOFF ZBMINI-L2 (ZBMINIL2) is a compact Zigbee 3.0 in-wall module for one lighting circuit that works without a neutral wire. It is fitted behind an existing switch in the back box and connects with L-in and L-out, so older installations with a live wire only can be made smart. Control is via a Zigbee gateway (remote, schedules, scenes) and locally via an existing wall switch or push button on terminals S1/S2, including two-way staircase wiring. The module switches up to 6 A at 100–240 V AC. For LED lighting the maximum is 300 W at 230 V, with a minimum load of 3 W and no separate anti-flicker module required. It is a Zigbee end device and therefore not a router: it does not extend the Zigbee network. Specifications Model: ZBMINIL2 Application: Light switching without neutral wire Supply: 100–240 V AC, 50/60 Hz Load: 6 A max.; LED 300 W max. at 230 V, 3 W minimum Protocol: Zigbee 3.0, end device (not a router) Control: Zigbee gateway plus wall switch or push button on S1/S2 Mounting: in-wall, suitable for EU/86/120 boxes Dimensions: 39.5 × 32 × 18.4 mm Operating temperature: −10 … 40 °C Have the mains installation carried out by a qualified installer, with a 6 A circuit breaker or RCBO upstream of the module. Do not connect an anti-flicker module or inductive loads such as fans. A Zigbee 3.0 gateway is required.
Product number: ZBMINIL2

€13.14*
New
SONOFF SNZB-01M Zigbee Wireless Switch (incl. battery)
The SONOFF SNZB-01M (Orb 4-In-1 from the Fusion series) is a wireless scene controller with four buttons. Each button recognises a single, double, triple and long press, so you can start up to 16 different scenes or actions. Compared with the single-button SNZB-01P it offers more scenes, a longer range and additional pairing options. The controller works in Zigbee mode via a Zigbee gateway or in eWeLink-Remote mode via an eWeLink-Remote gateway. With TouchLink you pair it directly with compatible Zigbee lamps, such as Philips Hue or IKEA, and bindings in Home Assistant allow direct device-to-device control. The wireless range is up to 130 m in open space. At 50 presses per day the CR2477 battery lasts at least four years in Zigbee mode and two years in eWeLink-Remote mode. Samsung SmartThings Hub V3 supports a maximum of 12 scenes. Specifications Model: SNZB-01M (Orb 4-In-1, Fusion) Application: Wireless scene control with four buttons Control: 4 buttons × 4 actions (single, double, triple, long press) = 16 triggers Protocol: Zigbee (IEEE 802.15.4) or eWeLink-Remote, switchable; TouchLink Battery: CR2477 (3 V), included Mounting: magnetic, adhesive or screw Dimensions: Ø 50 × 22.5 mm; 53 g Operating temperature: −10 … 60 °C A Zigbee gateway or an eWeLink-Remote gateway is required for use. The controller is suitable for wall mounting and as a portable remote, for indoor use only.
Product number: SNZB-01M

€16.45*
New
SONOFF NSPanel Smart Scene Wall Switch EU Black
The SONOFF NSPanel-EU (NSPanel Smart Scene Wall Switch, black version) is an 86 × 86 mm wall switch with two relays, a 3.5-inch touchscreen and a built-in temperature sensor. The two physical keys switch the connected loads; on the screen you control devices, groups and manual scenes from the same eWeLink account. As a thermostat the panel controls heating or cooling equipment based on its own temperature measurement, with up to six time periods in automatic mode. The screen also shows time, date and weather. Without a network connection the thermostat and screen functions that rely on the server are unavailable; on/off switching, the power-on state and inching remain controllable. LAN control is supported. The load per channel is 2 A (480 W), 4 A (960 W) in total. Specifications Model: NSPanel-EU Application: Wall switch with touchscreen, thermostat function and two relays Colour: black Supply: 100–240 V AC, 50/60 Hz, neutral wire required Load: 2 A (480 W) per channel, 4 A (960 W) total Protocol: Wi-Fi 2.4 GHz (IEEE 802.11 b/g/n) Display: 3.5-inch TFT touchscreen, 480 × 320 px Dimensions: 86 × 86 × 41.7 mm Operating temperature: −10 … 40 °C The panel works with live and neutral wires. Have the mains installation carried out by a qualified installer, with a suitable circuit breaker in the consumer unit.
Product number: NSPanel-EU

€41.24*