DIN-rail adapters for safe and professional installation of the FIBARO modules. This is the DIN-rail adapter with S1 and S2 buttons.Advantages of the S1 and S2 buttonsThe S1 and S2 buttons enable control via the DIN railVia the S1 button the module can be added/deleted from the Z-Wave networkEasy identification of the modules thanks to colours and labels
DIN-rail adapters for safe and professional installation of the FIBARO modules. This is the DIN-rail adapter with S1 and S2 buttons.Advantages of the S1 and S2 buttonsThe S1 and S2 buttons enable control via the DIN railVia the S1 button the module can be added/deleted from the Z-Wave networkEasy identification of the modules thanks to colours and labels
DIN-rail adapters for safe and professional installation of the FIBARO modules. This is the DIN-rail adapter with S1 and S2 buttons.Advantages of the S1 and S2 buttonsThe S1 and S2 buttons enable control via the DIN railVia the S1 button the module can be added/deleted from the Z-Wave networkEasy identification of the modules thanks to colours and labels
DIN-rail adapters for safe and professional installation of the FIBARO modules. This is the DIN-rail adapter with S1 and S2 buttons.Advantages of the S1 and S2 buttonsThe S1 and S2 buttons enable control via the DIN railVia the S1 button the module can be added/deleted from the Z-Wave networkEasy identification of the modules thanks to colours and labels
DIN-rail adapters for safe and professional installation of the FIBARO modules. This is the DIN-rail adapter with S1 and S2 buttons.Advantages of the S1 and S2 buttonsThe S1 and S2 buttons enable control via the DIN railVia the S1 button the module can be added/deleted from the Z-Wave networkEasy identification of the modules thanks to colours and labels
The Heatit Z-Water2 is a Z-Wave control unit for operating water-based heating systems. With this control unit, the electrical on/off valve controllers (actuators) on heating distributors can be controlled within a Z-Wave network.
The Z-Water2 is equipped with nine (9) potential-free switching contacts. These switching relays can be operated per output via the Z-Wave controller or linked via Z-Wave association to Heatit and other Z-Wave thermostats. In addition, the Z-Water2 has two inputs to which external NTC sensors can be connected for local temperature measurements.
Due to the DIN rail mounting, the Z-Water2 can be easily and professionally mounted near the mix manifold.
Potential free contacts
The potential-free switching relays of the Z-Water2 can switch a maximum of 5 Amps per output. This allows the common open/close valve controllers (actuators) that are offered on the heat installation market to be connected. Both 24VDC (via external power supply) and 230VAC actuators can be used.
Thermostat connection
The control of the Z-Water2 relay outputs can be done from climate panels of the Z-Wave controller used. It is also possible to connect thermostats from Heatit (such as TRM3, TRM6 and Z-Temp2) and other Z-Wave manufacturers via Z-Wave associations. This means that the linked thermostat directly controls the relay output on the Z-Water2.
'Valve exercise'
In the warmer period, the valve controllers (actuators) will be used less often or may not be used at all. To prevent limescale build-up from blocking the valve after a long period of time, the Z-Water2 has a 'valve exercise' option. This special function will open and close the connected actuator at least once every 30 days for a preset time (parameter). This prevents problems in the heating system.
As you would expect from a Heatit product, the latest Z-Wave functions are supported. This means that the Z-Water2 is already prepared for the future. Additional accessories will be available later, such as an external Z-Wave antenna and a separate Heatit 24VDC DIN-rail power supply.
Attributes
• Z-Wave communication
• Compact enclosure with DIN rail mounting
• Nine (9) Potential-free relays, individually controllable from controller
• Two (2) analog NTC (10kΩ) inputs for external temperature sensors
• Connection with Z-Wave thermostat possible (via associations)
• Connector for external antenna (optional, not yet available)
• Prepared for Z-Wave Security and SmartStart support (Z-Wave 3.0)
DIN-rail adapters for safe and professional installation of the FIBARO modules. This is the DIN-rail adapter with S1 and S2 buttons.Advantages of the S1 and S2 buttonsThe S1 and S2 buttons enable control via the DIN railVia the S1 button the module can be added/deleted from the Z-Wave networkEasy identification of the modules thanks to colours and labels
DIN-rail adapters for safe and professional installation of the FIBARO modules. This is the DIN-rail adapter with S1 and S2 buttons.Advantages of the S1 and S2 buttonsThe S1 and S2 buttons enable control via the DIN railVia the S1 button the module can be added/deleted from the Z-Wave networkEasy identification of the modules thanks to colours and labels
Vitrum DIN On-Off is a wireless Z-Wave switch for the control of 4 electrical devices. The maximum load per output is 16A. The product can be mounted on a DIN-rail and is equipped with 5 buttons for control and programming purposes.FeaturesZ-Wave switch for control of electrical devices and lightingDIN-rail mountingMaximum load capacity 16A per channel
DIN-rail adapters for safe and professional installation of the Nice DoubleDimmer-Control module. This is the DIN rail adapter without S1 and S2 buttons.
DIN-rail adapters for safe and professional installation of the FIBARO modules. This is the DIN-rail adapter with S1 and S2 buttons.Advantages of the S1 and S2 buttonsThe S1 and S2 buttons enable control via the DIN railVia the S1 button the module can be added/deleted from the Z-Wave networkEasy identification of the modules thanks to colours and labels
The SONOFF Basic DIN Rail Zigbee Smart Switch (BASIC-ZB1GSP) is a 1-module-wide Zigbee 3.0 switch for the consumer unit. It switches one final circuit up to 32 A (officially 7680 W maximum) at 100–240 V AC, 50/60 Hz, and it measures voltage, current, power and energy. According to SONOFF the contact is double-pole: both the phase and the neutral conductor are interrupted. Overload limits, schedules and scenes are set via a Zigbee 3.0 gateway.
It is intended for higher loads in the distribution board, always within the 32 A limit and the applicable installation rules. The housing is 84 × 66.5 × 18 mm and clips onto a standard DIN rail. SONOFF advises copper conductors of 4 to 10 mm². As a mains-powered Zigbee device it can also act as a Zigbee router and strengthen the mesh in the meter cupboard. Operating temperature: −15 to 50 °C.
Specifications
Model: BASIC-ZB1GSP
Mounting: DIN rail, 1 module wide (18 mm)
Supply/load: 100–240 V AC, 50/60 Hz, 32 A max. (7680 W)
Switching: double-pole (phase and neutral), according to SONOFF
Energy metering: voltage, current, power and consumption
Protocol: Zigbee 3.0; also a Zigbee router
Conductor size (official): 4–10 mm² copper
Dimensions: 84 × 66.5 × 18 mm; operating temperature −15 to 50 °C
Have installation in the consumer unit carried out by a qualified installer, with the correct upstream protection. A Zigbee 3.0 gateway is required; measurements and protection options may differ by gateway.
Vitrum DIN HVAC is a wireless Z-Wave control unit with 5 outputs, 3 for fan speed and 2 for valve control. The product can be DIN-rail mounted and is equipped with 5 buttons for control and programming purposes.FeaturesZ-Wave switch for HVAC controlDIN-rail mountingMaximum load capacity 5A
DIN-rail adapters for safe and professional installation of the Nice On/Off-Control2 module. This is the DIN-rail adapter with S1 and S2 buttons.Advantages of the S1 and S2 buttonsThe S1 and S2 buttons enable control via the DIN railVia the S1 button the module can be added/deleted from the Z-Wave networkEasy identification of the modules thanks to colours and labels
DIN-rail adapters for safe and professional installation of the Nice DoubleDimmer-Control module. This is the DIN-rail adapter with S1 and S2 buttons.Advantages of the S1 and S2 buttonsThe S1 and S2 buttons enable control via the DIN railVia the S1 button the module can be added/deleted from the Z-Wave networkEasy identification of the modules thanks to colours and labels
Vitrum DIN Double Shutter is a Z-Wave Plus switch for the operation of blinds and curtains. The product can be mounted on a DIN rail and is equipped with buttons for local control. To prevent damage to the motor, the outputs are interlocked.FeaturesZ-Wave switch for control of AC motorsMaximum load per output is 5AInterlocking between the two outputsTo be used with motors with mechanical limitExtended association groups
Vitrum DIN Dimmer is a Z-Wave Plus Dimmer for DIN-rail mounting. The dimmer works with the following dimming methods: phase cut and phase on. The product can be DIN-rail mounted and is equipped with buttons for local control.FeaturesZ-Wave Dimmer for lighting controlDIN-rail mountingMaximum load 200W LED
The Heatit DIN Smart Thermostat is an electronic DIN rail thermostat designed for electric heating. It can be controlled via Z-Wave® (with a gateway), Modbus RS-485, or manually using the front buttons. With its clear display and versatile connection options, it offers a user-friendly and professional solution for both residential and industrial applications.
Features
DIN rail mounting for easy installation in distribution or control panels.
Supports Z-Wave® and Modbus RS-485 for flexible integration in smart home or building automation systems.
Three modes: Heat, Cool and Eco for precise temperature control across various applications.
Connections for two external temperature sensors (room and floor sensors, wired).
Active power metering for real-time insight into energy consumption and improved efficiency.
ZeroX™ technology ensures the relay switches at 0V, significantly extending its lifespan.
Supports hysteresis and PWM regulation for stable temperature management.
Open window detection automatically switches off heating to prevent energy loss.
Built-in overload and overheat protection for safe operation.
Compatible with OTA firmware updates and SmartStart setup.
Supports external antenna (optional) for improved signal strength.
Technical specifications
Power supply: 230VAC / 50Hz
Max load: 16A / 3600W (resistive load)
For loads above 13A, a contactor is recommended
Control methods: Hysteresis or PWM
Communication: Z-Wave® (S2 security, SmartStart) / Modbus RS-485
Operating temperature: 0–50 °C
Mounting: DIN rail (1 module width)
Protection class: IP20 (for installation inside distribution box)
The SONOFF Basic DIN Rail Matter Over Wi-Fi (BASIC-1GSP) is the Matter variant of the 1-module-wide DIN-rail switch for one final circuit up to 32 A (officially 7680 W maximum). It measures voltage, current, power and energy, and overload limits and schedules can be set. According to SONOFF the contact is double-pole: both the phase and the neutral conductor are interrupted. The connection is Matter over Wi-Fi on 2.4 GHz: no Zigbee gateway is required, but a Matter controller is.
Choose this version when the installation already runs on Matter — for example Apple Home or Home Assistant — and you want to switch and monitor a powerful circuit from the distribution board. Mounting is on a standard DIN rail, housing 84 × 66.5 × 18 mm, recommended conductor size 4–10 mm² copper. Operating temperature −15 to 50 °C. Extended energy statistics remain available in eWeLink alongside Matter control.
Specifications
Model: BASIC-1GSP
Mounting: DIN rail, 1 module wide (18 mm)
Supply/load: 100–240 V AC, 50/60 Hz, 32 A max. (7680 W)
Switching: double-pole (phase and neutral), according to SONOFF
Energy metering: voltage, current, power and consumption
Protocol: Matter over Wi-Fi, 2.4 GHz
Conductor size (official): 4–10 mm² copper
Dimensions: 84 × 66.5 × 18 mm; operating temperature −15 to 50 °C
A compatible Matter controller is required. Have installation in the consumer unit carried out by a qualified installer, with the correct upstream protection. This model does not build a Zigbee mesh; for that, BASIC-ZB1GSP is the separate Zigbee variant.