The Heatit Actuator is an electrothermal actuator intended to open and close water-based heating systems. The actuator is normally closed and, in addition to being opened with a signal from a thermostat or actor, can also be operated manually. Features M30 x 1.5mm Voltage 230VStart current 300 mAPower 1WIP54 Stroke 5mm +/- 1m cable Normally closed

Heatit ZM Single Relay is a built-in relay for control of electrical devices up to 16A. The relay can be controlled via the Z-Wave network or a connected switch. The module has support for scene activation and a power measurement function. Heatit ZM Single Relay supports SmartStart and has a Z-Wave 700 series chip. The compact module has a thickness of 25 mm and fits into a flush-mounting box.FeaturesPowerful built-in relay 16A / 3600WZ-Wave 700SmartStartSupport for scene activationFirmware update (OTA)Power measurementSupports encryption modes S0, S2 Authenticated Class, S2 Unauthenticated Class

6 metres temperature sensor (3mm thickness)

Heatit Z-Push Wall Controller is a battery-operated Z-Wave wall switch. The switch can be equipped with 1, 2 or 3 push buttons for activating scenarios and controlling associations. Each push button has a two-colour LED indicator to show button actions. The switch operates on a button cell battery and fits into system 55 frames. The Z-Push Wall Controller is available in the colours RAL 9003 (white), RAL 9010 (cream white) and Black.Information about push buttonsZ-Push Wall Controller comes with a set of different push buttons. The buttons can be configured as follows:Single = 1x below, 1x aboveDouble = 2x below, 2x aboveTriple = 3x below , 3x above

Heatit Z-Push Wall Controller is a battery-operated Z-Wave wall switch. The switch can be equipped with 1, 2 or 3 push buttons for activating scenarios and controlling associations. Each push button has a two-colour LED indicator to show button actions. The switch operates on a button cell battery and fits into system 55 frames. The Z-Push Wall Controller is available in the colours RAL 9003 (white), RAL 9010 (cream white) and Black.Information about push buttonsZ-Push Wall Controller comes with a set of different push buttons. The buttons can be configured as follows:Single = 1x below, 1x aboveDouble = 2x below, 2x aboveTriple = 3x below , 3x above

Z-Smoke is a multifunctional Z-Wave smoke detector with 230V connection and backup battery. Besides smoke detection, the Z-Smoke also contains a motion sensor, temperature sensor (heat detection) and emergency LED. The motion sensor can be used as a trigger via a Z-Wave controller. Multiple Z-Smoke's can be wirelessly linked through associations.FeaturesMulti-purpose smoke detector with multiple sensorsPossibility to link Z-Smokes for alarmsBuilt-in motion detector can be used for scenes and notifications via controllerCan be paired with up to 6 Z-Smoke detectorsCeiling connection with 230V and built-in backup battery

Z-Dim works with various light sources (from 1W), including: halogen and incandescent lamps, LED lighting, dimmable LED drivers and electronic transformers. The dimmer is equipped with an extra input, so that Z-Dim can easily be applied in a hallway or stairwell. The switch fits in frames of brands such as: GIRA System 55, Elko and Schneider Exxact. Z-Dim is supplied with 2 rotary switches and central plates in the colours: RAL9010 and RAL9003. Important: Heatit Z-Dim requires L + N. The connection of a light source is not required, Z-Dim can also control Z-Wave devices via association and scene activation.

Heatit Z-Push Wall Controller is a battery-operated Z-Wave wall switch. The switch can be equipped with 1, 2 or 3 push buttons for activating scenarios and controlling associations. Each push button has a two-colour LED indicator to show button actions. The switch operates on a button cell battery and fits into system 55 frames. The Z-Push Wall Controller is available in the colours RAL 9003 (white), RAL 9010 (cream white) and Black.Information about push buttonsZ-Push Wall Controller comes with a set of different push buttons. The buttons can be configured as follows:Single = 1x below, 1x aboveDouble = 2x below, 2x aboveTriple = 3x below , 3x above

Z-DIN 616 is equipped with 6 x 16A potential-free relays. The module has 6 digital inputs and 6 relay switches for DIN rail mounting. The relays can be switched independently and can be used for AC and DC loads. The Z-DIN is powered with a 10 - 24 DC power adapter.

The Heatit Z-Temp3 is a battery-powered thermostat specifically designed for controlling water-based heating systems. In combination with the Heatit Z-Water2 you can control your heating system via the Z-Wave® network or with the buttons on the control panel. The thermostat has a user-friendly interface.The Heatit Z-Temp3 has 3 settings: Heating, Cooling and Eco.The thermostat fits into System 55 frames and can be mounted next to other devices such as dimmers or light switches. The Heatit Z-Temp3 can also be mounted directly on the wall or placed freely.The Heatit Z-Temp3 can be set as a main thermostat. This means that you can set the desired temperature and mode on one device, after which it will automatically forward the settings to other connected units.All communication between the Heatit Z-Temp3 and the controlled device are completely wireless.The Heatit Z-Temp3 runs on 2x AAA batteries, but can also be connected to an external power source. For this purpose the Heatit Transformer 230VAC (45 126 48) is recommended.The Heatit Z-Temp3 can be connected to the Heatit ZM Single Relay, other Z-Wave relays , the Heatit ZM Thermostat, the Heatit Z-TRM6 Thermostat and other Z-Wave devices to control different types of heating solutions.The Heatit Z-Temp3 is an excellent choice for renovation or restoration projects of existing buildings, as it is easy to install without cabling. We recommend using multiple 230VAC devices to create a mesh network.FeaturesDisplay shows measured and set temperatureHas 3 settings: Heating, Cooling and Eco.Battery-powered thermostat for wireless control of Z- Wave relayBuilt-in temperature and humidity sensorIdeal for controlling individual heating zones with Z-WaterAvailable in 2 colorsInternal temperature sensor Proximity sensor for automatic on/off display

Accessory for the FIBARO Home Center 3 Lite. The Ethernet Adapter Micro-USB to RJ45 with 10/100 Mbps.FeaturesConnect the Home Center 3 Lite to the network via an Ethernet cablePlug & Play installation, no drivers requiredUse a separate USB power supply for the Ethernet adapter (USB power supply not included)

The Heatit Z-Water2 is a Z-Wave control unit for operating water-based heating systems. With this control unit, the electrical on/off valve controllers (actuators) on heating distributors can be controlled within a Z-Wave network. The Z-Water2 is equipped with nine (9) potential-free switching contacts. These switching relays can be operated per output via the Z-Wave controller or linked via Z-Wave association to Heatit and other Z-Wave thermostats. In addition, the Z-Water2 has two inputs to which external NTC sensors can be connected for local temperature measurements. Due to the DIN rail mounting, the Z-Water2 can be easily and professionally mounted near the mix manifold. Potential free contacts The potential-free switching relays of the Z-Water2 can switch a maximum of 5 Amps per output. This allows the common open/close valve controllers (actuators) that are offered on the heat installation market to be connected. Both 24VDC (via external power supply) and 230VAC actuators can be used. Thermostat connection The control of the Z-Water2 relay outputs can be done from climate panels of the Z-Wave controller used. It is also possible to connect thermostats from Heatit (such as TRM3, TRM6 and Z-Temp2) and other Z-Wave manufacturers via Z-Wave associations. This means that the linked thermostat directly controls the relay output on the Z-Water2. 'Valve exercise' In the warmer period, the valve controllers (actuators) will be used less often or may not be used at all. To prevent limescale build-up from blocking the valve after a long period of time, the Z-Water2 has a 'valve exercise' option. This special function will open and close the connected actuator at least once every 30 days for a preset time (parameter). This prevents problems in the heating system. As you would expect from a Heatit product, the latest Z-Wave functions are supported. This means that the Z-Water2 is already prepared for the future. Additional accessories will be available later, such as an external Z-Wave antenna and a separate Heatit 24VDC DIN-rail power supply. Attributes • Z-Wave communication • Compact enclosure with DIN rail mounting • Nine (9) Potential-free relays, individually controllable from controller • Two (2) analog NTC (10kΩ) inputs for external temperature sensors • Connection with Z-Wave thermostat possible (via associations) • Connector for external antenna (optional, not yet available) • Prepared for Z-Wave Security and SmartStart support (Z-Wave 3.0)

The Heatit Z-TRM6 is a Z-Wave thermostat for operating electric underfloor heating. The thermostat is equipped with a built-in temperature sensor and has two inputs for external temperature sensors. The thermostat can be operated via a Z-Wave controller or the physical buttons on the front. The thermostat supports active energy metering and various types of protections. The maximum load capacity of the thermostat is 16A. You can also manually set the current measurement, for example if the thermostat is connected to an external relay. The TRM6 is equipped with the following protections: overheating, overload and short circuit in the sensor. The cover frames of the Z-TRM6 are made on the basis of the 55x55 frame standard and tested on the GIRA ST55, Elko and Schneider Exact. The installation depth of the module is 23.5 mm. Different modes The Heatit Z-TRM6 can be used in three functional ways: heating, cooling and eco. Each chosen mode will control the internal relay, only the logic will react differently to the sensor data. With the Eco Mode, the thermostat can be (temporarily) set to a lower set point, for example during the holiday or summer period. You can activate this via the physical thermostat or a scene via the gateway. Master thermostat The Heatit Z-TRM6 can be set as a MASTER thermostat. Setpoints cannot be sent to the FIBARO Heat Controller or Heatit Z-Temp2, but the Z-TRM6 can send temperature settings to other thermostats (via associations), including the Heatit ZM Thermostat. Waterborne heating In combination with the Z-Water (and other Z-Wave switches), the TRM6 can be used for water-based underfloor heating. In addition, the Heatit Z-TRM6 supports a 'Power Regulator Mode'. This Power Regulator Mode switches the internal relay on and off every X time to heat or cool the room, without using a temperature sensor. For example, the Z-TRM6 switches the internal relay on and then off every 30 minutes. Features Display shows measured temperature Buttons for manual operation Mounted in flush-mounted box, works on 230V connection Temperature measurement: internal and external wired sensors (floor or room) Fits in GIRA ST55 frames Available in 2 colors Active energy metering Temperature control: Hysteresis or PWM Relay status icon Adjustable display brightness Lock Mode/Child Lock Open Window Detection ZeroX detection (zero crossing switching).

6 metres temperature sensor (3mm thickness)

The Heatit Z-Temp3 is a battery-powered thermostat specifically designed for controlling water-based heating systems. In combination with the Heatit Z-Water2 you can control your heating system via the Z-Wave® network or with the buttons on the control panel. The thermostat has a user-friendly interface.The Heatit Z-Temp3 has 3 settings: Heating, Cooling and Eco.The thermostat fits into System 55 frames and can be mounted next to other devices such as dimmers or light switches. The Heatit Z-Temp3 can also be mounted directly on the wall or placed freely.The Heatit Z-Temp3 can be set as a main thermostat. This means that you can set the desired temperature and mode on one device, after which it will automatically forward the settings to other connected units.All communication between the Heatit Z-Temp3 and the controlled device are completely wireless.The Heatit Z-Temp3 runs on 2x AAA batteries, but can also be connected to an external power source. For this purpose the Heatit Transformer 230VAC (45 126 48) is recommended.The Heatit Z-Temp3 can be connected to the Heatit ZM Single Relay, other Z-Wave relays , the Heatit ZM Thermostat, the Heatit Z-TRM6 Thermostat and other Z-Wave devices to control different types of heating solutions.The Heatit Z-Temp3 is an excellent choice for renovation or restoration projects of existing buildings, as it is easy to install without cabling. We recommend using multiple 230VAC devices to create a mesh network.FeaturesDisplay shows measured and set temperatureHas 3 settings: Heating, Cooling and Eco.Battery-powered thermostat for wireless control of Z- Wave relayBuilt-in temperature and humidity sensorIdeal for controlling individual heating zones with Z-WaterAvailable in 2 colorsInternal temperature sensor Proximity sensor for automatic on/off display

Z-Dim works with various light sources (from 1W), including: halogen and incandescent lamps, LED lighting, dimmable LED drivers and electronic transformers. The dimmer is equipped with an extra input, so that Z-Dim can easily be applied in a hallway or stairwell. The switch fits in frames of brands such as: GIRA System 55, Elko and Schneider Exxact. Z-Dim is supplied with 2 rotary switches and central plates in the colours: RAL9010 and RAL9003. Important: Heatit Z-Dim requires L + N. The connection of a light source is not required, Z-Dim can also control Z-Wave devices via association and scene activation.

Z-Smoke is a multifunctional Z-Wave smoke detector that operates on 3x CR123A. Besides smoke detection, Z-Smoke also contains a motion sensor and temperature sensor (heat detection). The motion sensor can be used as a trigger via a Z-Wave controller.Multiple Z-Smoke can be wirelessly linked to a Z-Smoke 230V through associations.FeaturesMultifunctional smoke detector with multiple sensorsBattery powered smoke detectorPossibility to link Z-Smokes together for alarmsBuilt-in motion detector can be used for scenes and notifications via controllerPairing with up to 6 Z-Smokes 230V

The Heatit External Room Sensor is an external NTC sensor (10k Ohm) for measuring the temperature. The sensor has been specially developed for the Heatit thermostats. The sensor can be mounted directly on the wall or on a flush-mounted box. The sensor fits in a System 55 frame. Installation instructions It is not possible to connect the sensors in parallel or series. When used in combination with a thermostat, dimmer or other products that radiate heat, it is recommended to mount the sensor under the other product.

The Heatit Z-TRM6 is a Z-Wave thermostat for operating electric underfloor heating. The thermostat is equipped with a built-in temperature sensor and has two inputs for external temperature sensors. The thermostat can be operated via a Z-Wave controller or the physical buttons on the front. The thermostat supports active energy metering and various types of protections. The maximum load capacity of the thermostat is 16A. You can also manually set the current measurement, for example if the thermostat is connected to an external relay. The TRM6 is equipped with the following protections: overheating, overload and short circuit in the sensor. The cover frames of the Z-TRM6 are made on the basis of the 55x55 frame standard and tested on the GIRA ST55, Elko and Schneider Exact. The installation depth of the module is 23.5 mm. Different modes The Heatit Z-TRM6 can be used in three functional ways: heating, cooling and eco. Each chosen mode will control the internal relay, only the logic will react differently to the sensor data. With the Eco Mode, the thermostat can be (temporarily) set to a lower set point, for example during the holiday or summer period. You can activate this via the physical thermostat or a scene via the gateway. Master thermostat The Heatit Z-TRM6 can be set as a MASTER thermostat. Setpoints cannot be sent to the FIBARO Heat Controller or Heatit Z-Temp2, but the Z-TRM6 can send temperature settings to other thermostats (via associations), including the Heatit ZM Thermostat. Waterborne heating In combination with the Z-Water (and other Z-Wave switches), the TRM6 can be used for water-based underfloor heating. In addition, the Heatit Z-TRM6 supports a 'Power Regulator Mode'. This Power Regulator Mode switches the internal relay on and off every X time to heat or cool the room, without using a temperature sensor. For example, the Z-TRM6 switches the internal relay on and then off every 30 minutes. Features Display shows measured temperature Buttons for manual operation Mounted in flush-mounted box, works on 230V connection Temperature measurement: internal and external wired sensors (floor or room) Fits in GIRA ST55 frames Available in 2 colors Active energy metering Temperature control: Hysteresis or PWM Relay status icon Adjustable display brightness Lock Mode/Child Lock Open Window Detection ZeroX detection (zero crossing switching).

De Heatit DIN Transformer 24V is een compacte DIN rail gemonteerde transformator met een breedte van 51mm. De transformator zet 230V AC om naar 24V. De 24V voeding is speciaal ontwikkeld voor gebruik samen met de Heatit Z-Water2 en de 24V actuatoren. Maar deze voeding is zeker ook te gebruiken voor andere laagspanningsoplossingen zo is deze ook perfect te combineren met de Aqara G4 Deurbel. Kenmerken DIN rail gemonteerd (35mm)51mm breed2 DIN breedte 24V DC 2.5A/60WVoltage verstelbaar tussen 23-25V

Z-Dim works with various light sources (from 1W), including: halogen and incandescent lamps, LED lighting, dimmable LED drivers and electronic transformers. The dimmer is equipped with an extra input, so that Z-Dim can easily be applied in a hallway or stairwell. The switch fits in frames of brands such as: GIRA System 55, Elko and Schneider Exxact. Z-Dim is supplied with 2 rotary switches and central plates in the colours: RAL9010 and RAL9003. Important: Heatit Z-Dim requires L + N. The connection of a light source is not required, Z-Dim can also control Z-Wave devices via association and scene activation.

The Renergy Quick App is the most user-friendly way to automatically operate large-scale electrical consumers based on the spot price. With the QA it is possible to have these devices automatically avoid the most expensive prices. In terms of devices, you can think of the electric underfloor heating, an electric boiler and the car charging station. As a user, you only have to determine how many hours per day these devices are operated. The Quick App automatically ensures that the most expensive hours of the day are avoided. In addition, when purchasing Renergy you receive access to 4 additional integrations for operating a charging station or infrared panel.  As an Renergy user you can choose any energy supplier that offers dynamic energy rates. Furthermore, there are no subscription or other hidden costs for automating based on the spot price. Renergy collects the spot prices from Nord Pool every day. Thanks to this integration, the spot price per hour becomes clear on a daily basis and can be automated accordingly. As a user, you can then set the individual hours to avoid the price for electric heating, boiler and charging station. When importing Renergy, several Events, Variables and Child Devices are created in the system. This makes it incredibly easy to switch the desired devices based on the spot price.   Additional integrations The Renergy Quick App comes with two additional types of integrations from four different brands. The first type is an integration of a smart charging station, which works with the Easee and Zaptec charging stations. The second type is an integration of a smart infrared panel, which works with the panels of Mill and Adax. Easee & Zaptec with the FIBARO HC3 / HC3L With these Quick Apps it is possible to integrate a charging station from Easee or Zaptec. With both integrations, it is possible to operate the charging station individually and to include it in the automation with Renergy. The QA also monitors the active and total energy consumption. Adax & Mill with the FIBARO HC3 / HC3L With these Quick Apps it is possible to integrate an infrared panel from Adax or Mill. With both integrations it is possible to operate the panel individually and to include it in the automation with Renergy. The QA also monitors the active and total energy consumption. Energy Panel Pro The Energy Panel Pro QA displays the data of the energy panel and the connected devices from the FIBARO PRO smart home system in the most user-friendly way.   Notes The Quick App is not a product of FIBARO; The supplier and developer are not liable for API availability and manufacturer changes. If bugs or problems arise with the Quick App, they will be resolved on a best effort & be resolved fair-use; The Quick App has been developed based on available documentation from FIBARO. The operation and support of this Quick App is limited to the API options that FIBARO offers. Renergy works independently of your energy supplier. Infrastructure device automation with Renergy requires smart devices or integrations to operate them. Contact us for more information. A P1 Meter is required to keep track of the total consumption. The P1 Meter WiFi Gateway is recommended for this. https://shop.jdkbenelux.com/P1- Meter-WiFi-Gateway-Quick-App-for-HC3-HC3L/P1M-WG   Features Automate based on spot price with FIBARO; Avoid the most expensive prices for electric heating, boiler and car charging; Use the cheapest prices for charging a home battery; Optimized for the Yubii App; No subscription costs for the end user; Works with the FIBARO Home Center 3 and Home Center 3 Lite;

The Heatit ZM Dimmer is a Z-Wave built-in dimmer with active consumption measurement. The ZM Dimmer can be used in 2- and 3-wire installations. The dimmer can be used to control LED lighting from 5W – 250W. The module is equipped with an intelligent auto-calibration mechanism and works on most low loads. With the auto calibration, the dimmer checks the minimum and maximum load capacity. You can adjust the min. load capacity via the physical button on the module and via a Z-Wave gateway. When connecting low loads, it is recommended to use a bypass. The ZM Dimmer has two inputs for connecting a switch. The first input is for controlling the connected lamp. The second input is for scene activation only. In addition, the ZM Dimmer is equipped with various protections, including overload protection, overvoltage and overheating. Finally, the ZM Dimmer can be used as a switch for non-dimmable sources for switching LED lighting, for example. A 3-wire installation is required. Features Z-Wave 800 LED: 5 – 250W Installation in 2- and 3-wire installations Second input for scene switch Works with trailing edge and trailing edge Manual min. dimmability setting via physical button Auto calibration for min & max. dimmability setting Protections against: overload, overvoltage, short circuit and overheating

Z-Repeater is a multifunctional Z-Wave range extender with 2 USB ports. The Z-Repeater is ideal to extend the coverage of the Z-Wave network to blind spots. Thanks to the rechargeable back-up battery, the device works for up to 6 hours. This keeps important battery-powered devices in contact with the Z-Wave controller during a power failure.

De Heatit Transformer is een compacte inbouw transformator voor Europese inbouwdozen. De transformator zet 230V AC om naar 12V DC, 5V DC, of 3,3V DC. Hierdoor kan je laagspanningsapparaten aansluiten op het lichtnet. In combinatie met Heatit batterijadapters, waaronder de Temp2 Battery Adapter, kan de Heatit Transformer de batterijgevoede apparaten met netstroom voeden. Alle apparaten op een batterijen met een stroomverbruik tot 450mA bij 12V DC, 420mA bij 5V DC en 3,3V DC kunnen op de transformator worden aangesloten. Verder kan de Heatit Transformer gebruikt worden met volgende producten: FIBARO Smart Implant, FIBARO Walli ControllerMCO Home Boiler Thermostat, MCO Home CO2 Sensor (12V), MCO Home PM2.5 Sensor (12V) MCO Home Multi-Sensor A8-9Qubino 0-10V DimmerAeotec MultiSensor 6, Aeotec MultiSensor 7Kenmerken Kenmerken Compacte inbouw transformator Eenvoudig te installerenWalli Controller: Permanente stroomvoorziening voor de Walli Controller. Zorgt dat de LED te gebruiken is van de Walli Controller

3 metres temperature sensor (4mm thickness)

Surface mount box for external sensor installation

The Heatit External Room Sensor is an external NTC sensor (10k Ohm) for measuring the temperature. The sensor has been specially developed for the Heatit thermostats. The sensor can be mounted directly on the wall or on a flush-mounted box. The sensor fits in a System 55 frame. Installation instructions It is not possible to connect the sensors in parallel or series. When used in combination with a thermostat, dimmer or other products that radiate heat, it is recommended to mount the sensor under the other product.

The Heatit Actuator 24Vis an electrothermal actuator intended to open and close water-based heating systems. The actuator is normally closed and, in addition to being opened with a signal from a thermostat or actor, can also be operated manually. Features M30 x 1.5mm Voltage 24v DC (direct voltage) Start current 470mA Power 1WIP54 Stroke 5mm +/- 1m cable Normally closed

The Z-Relay is a relay (25A) for operating the boiler, detecting leaks, temperature control and outdoor applications. The module has three inputs, these are both The module has three inputs, which are both analogue and digital and can also be combined. The IP55 housing makes the module is suitable for outdoor applications.