Shelly Wave Motion | QLMO-003FEU

Battery life:	Tot 2 jaar, afhankelijk van gebruik
Battery type:	CR123A
Dimensions Product:	35 x 35 x 7 mm
Operating humidity:	30% to 70% RH
Operating temperature:	-20°C to 40°C
Protocol:	868, Z-Wave, Z-Wave 800, Z-Wave Long Range, Z-Wave Mesh Network
Range:	Max. 40 m binnenshuis (afhankelijk van omgeving)
Sensors:	PIR + Lichtsensor

Shelly Wave Pro Dimmer 1PM

The Shelly Wave Pro Dimmer 1PM is a DIN-rail-mounted dimmer. The module supports active energy measurement and is designed to dim a single light source. The Wave Pro Dimmer 1PM can be operated with 2 switches. The smart dimmer works with Z-Wave, using a Z-Wave 800 chipset, and is compatible with Homey, Home Center 3, and other platforms such as Home Assistant and SmartThings. You can easily install the dimmer in your fuse box on a DIN rail, allowing you to dim one light source with a maximum of 200 watts. Note! The dimmer does not yet have full support on the mentioned platforms. Check the current compatibility via the manual link below. Based on our own tests on the HC3, it seems possible to add the unit after several attempts, resulting in a usable endpoint. Note that the unit needs to be added in Singlechannel mode (see associations) and corrected. Supported Light Sources Incandescent bulbs Dimmable LED and CFL Dimmable electronic transformers Features 110-240VAC Z-Wave 800 chipset S2 security Maximum 200 watts (1 channel) 2 switch contacts Trailing edge Power measurement Overload protection Overheat protection Surge protection Fuse box installation, DIN rail 19mm width Manual

Product number: QPDM-0A1P01EU

€78.00*

Shelly Qubino Wave 1

The Shelly Qubino Wave 1 module is a Z-Wave 800 built-in switch with one potential-free output. The module is designed to control devices such as electric locks, garage doors, entrance gates, irrigation systems, electrical outlets and lighting. With a maximum load capacity of 16A, the module offers sufficient power for various applications. It is possible to control the module wirelessly via Z-Wave, as well as using a wall switch. The module can be powered with a voltage of 110-240V AC, 24-48V DC or 12V DC, providing flexibility in power supply. In addition, the output is potential-free, which means that the input voltage can differ from the device you want to switch. This allows compatibility with various electrical devices. In addition, the module is equipped with protection against overheating. Features Z-Wave 800 series Switch with potential-free output Maximum load capacity: 16A Protected against overheating Supports over-the-air firmware updates (OTA) Use with different types of switches

Product number: QNSW-001X16EU

€34.00*

Shelly Qubino Wave 1 Mini

The Shelly Qubino Wave 1 mini module is a Z-Wave 800 built-in switch with one dry or potential-free contact and one switch. The module is designed to control devices such as gates, garage doors and other electrical appliances. It is possible to control the module wirelessly via Z-Wave, as well as using a single wall switch. The module can be powered with a voltage of 110-240V AC. The potential-free contact has a maximum load capacity at 230v of 8A or 5A at 30V DC.Features Z-Wave 800 series Potential free switchMaximum load capacity at 230V AC - 8A / 30V DC 5ASupports over-the-air firmware updates (OTA) Can be used with different types of switches S2 security and SmartStart suitable Format 29x35x16 mm Wire 0.5 to 1.5 mm²

Product number: QMSW–0A1X8EU

€31.00*

Shelly Qubino Wave 1PM

The Shelly Qubino Wave 1 module is a Z-Wave 800 built-in switch with one potential-free output. The module is designed to control devices such as electric locks, garage doors, entrance gates, irrigation systems, electrical outlets and lighting. With a maximum load capacity of 16A, the module offers sufficient power for various applications. It is possible to control the module wirelessly via Z-Wave, as well as using a wall switch. The module can be powered with a voltage of 110-240V AC, 24-48V DC or 12V DC, providing flexibility in power supply. In addition, the output is potential-free, which means that the input voltage can differ from the device you want to switch. This allows compatibility with various electrical devices. In addition, the module is equipped with protection against overheating. Features Z-Wave 800 series Switch with potential-free output Maximum load capacity: 16A Protected against overheating Supports over-the-air firmware updates (OTA) Use with different types of switches

Product number: QNSW-001P16EU

€35.00*

Shelly Qubino Wave 1PM Mini

The Shelly Qubino Wave 1PM Mini module is a Z-Wave 800 built-in switch with one output and one switch. The module supports active energy metering and is designed to control devices such as lighting, sockets, heaters and other electrical appliances. It is possible to control the module wirelessly via Z-Wave, as well as using a single wall switch. The module can be powered with a voltage of 110-240V AC. The maximum load capacity is 8A. In addition, the module is equipped with multiple protection functions, including protection against overheating, overvoltage and overcurrent. Features Z-Wave 800 series Maximum load capacity at 8A Protected against overheating Supports over-the-air firmware updates (OTA) Can be used with different types of switchesS2 security and SmartStart suitableFormat 29x35x16 mmWire 0.5 to 1.5 mm²

Product number: QMSW–0A1P8EU

€33.00*

Shelly Qubino Wave 2PM

The Shelly Qubino Wave 2PM module is a Z-Wave 800 built-in switch with two outputs. The module supports active energy metering and is designed to control devices such as lighting, fans, infrared panels, heaters and other electrical appliances. It is possible to control the module wirelessly via Z-Wave, as well as using a wall switch. The module can be powered with a voltage of 110-240V AC or 24DC, providing flexibility in the power supply. The maximum load capacity at AC is 16A and at DC it is 10A. The outputs of the Wave 2PM can switch 10A individually and 16A combined. In addition, the module is equipped with multiple protection functions, including protection against overheating, overvoltage and overcurrent. Features Z-Wave 800 series Maximum load capacity at AC: 16A, at DC: 10A Protected against overheating Supports over-the-air firmware updates (OTA) Use with different types of switches

Product number: QNSW-002P16EU

€38.00*

Shelly Qubino Wave i4

This Shelly Qubino Wave i4 is a Z-Wave 800 module suitable for 4 switching contacts and is powered by 230v. The module sends Central Scene commands and/or associations when one of the buttons is used in the following way (see manual for more explanation): Press 1x brieflyPress 2x brieflyPress 1x and holdReleaseFeaturesZ-Wave 800110-240VAC Recessed, behind (wall) switch(es)Works with switch, pulse switch, hotel switchSwitch connection 4xManual

Product number: QNSN-0A24XEU

€31.00*

Shelly Qubino Wave i4DC

This Shelly Qubino Wave i4DC is a Z-Wave 800 module suitable for 4 switching contacts and is powered by 5-24v DC (direct voltage). The module sends Central Scene commands and/or associations when one of the buttons is used in the following way (see manual for more explanation) :Press 1x briefly Press 2x briefly Press once and hold Letting go Features Z-Wave 800 5-24V DCRecessed, behind (wall) switch(es) Works with switch, pulse switch, hotel switch Switch connection 4xManual

Product number: QNSN-0D24XEU

€31.00*

Shelly Qubino Wave PM Mini

The Shelly Qubino Wave PM mini module is a Z-Wave 800 built-in module for current measurement. The module is designed for current measurement of devices such as lighting, sockets, heaters and other electrical appliances. The module can be powered with a voltage of 110-240V AC. The maximum load capacity is 16A. Features Z-Wave 800 series Maximum load capacity 16A Supports over-the-air firmware updates (OTA) S2 security and SmartStart suitableFormat 29x35x16 mmWire 0.5 to 1.5 mm²

Product number: QMEM–0A1PC16EU

€30.00*

Shelly Qubino Wave Pro 1

The Shelly Qubino Wave Pro 1 is a Dinrail mountable Z-Wave 800 actor. The module is designed to operate 1 device such as lighting, fans, infrared panels, heaters and other electrical appliances. It is possible to operate the module wirelessly via Z-Wave, as well as using a (wall) switch. The maximum load capacity is 16A. Supported load types Resistive (Ohms) – Incandescent, halogen, heaters Capacitive – Electronic equipment with capacitors Inductive (with RC Snubber) – LED lighting, LED drivers, air conditioning and fans Attention! The switch-on peak of inductive loads such as LED lighting damages the relays. Use the RC Snubber to absorb this switch-on peak. Features Z-Wave 800 110-240VAC Output 1x16ASwitch connection 2x Protected against overload Protected against overheating Protected against voltage peaks Built-in distribution box, DIN-RailManual

Product number: QPSW-0A1X16EU

€63.00*

Shelly Qubino Wave Pro 1PM

The Shelly Qubino Wave Pro 1PM is a Dinrail mountable Z-Wave 800 actor. The module supports active energy measurement and is designed to control 1 device such as lighting, fans, infrared panels, heaters and other electrical appliances. It is possible to operate the module wirelessly via Z-Wave, as well as using a (wall) switch. The maximum load capacity is 16A. Supported load types Resistive (Ohms) – Incandescent, halogen, heaters Capacitive – Electronic equipment with capacitors Inductive (with RC Snubber) – LED lighting, LED drivers, air conditioning and fans Caution! The switch-on peak of inductive loads such as LED lighting damages the relays. Use the RC Snubber to absorb this switch-on peak. Features Z-Wave 800 110-240VAC Output 1x16ASwitch connection 2xCurrent measurement Protected against overload Protected against overheating Protected against voltage peaks Built-in distribution box, DIN rail Manual

Product number: QPSW-0A1P16EU

€78.00*

Shelly Qubino Wave Pro 2

The Shelly Qubino Wave Pro 2 is a Dinrail mountable Z-Wave 800 actor. The module is designed to control 2 devices such as lighting, fans, infrared panels, heaters and other electrical appliances. It is possible to operate the module wirelessly via Z-Wave, as well as using a (wall) switch. The maximum load capacity is 16A per channel and a combined maximum of 25A. Supported load types Resistive (Ohms) – Incandescent, halogen, heaters Capacitive – Electronic equipment with capacitors Inductive (with RC Snubber) – LED lighting, LED drivers, air conditioning and fans Note! The switch-on peak of inductive loads such as LED lighting damages the relays. Use the RC Snubber to absorb this switch-on peak. FeaturesZ- Wave800 110-240VAC Output 2x16A, max 25A totalSwitch connection 2xProtected against overload Protected against overheating Protected against voltage peaks Built-in distribution box, DIN-RailManual

Product number: QPSW-0A2X16EU

€73.00*

Shelly Qubino Wave Pro 2PM

The Shelly Qubino Wave Pro 2PM is a Dinrail mountable Z-Wave 800 actor. The module supports active energy metering and is designed to control 2 devices such as lighting, fans, infrared panels, heaters and other electrical appliances. It is possible to operate the module wirelessly via Z-Wave, as well as using a (wall) switch.The maximum load capacity is 16A per channel and a combined maximum of 25A.Supported load typesResistive (Ohmic) – Incandescent lamp, halogen, heating appliancesCapacitive – Electronic equipment with capacitorsInductive (with RC Snubber) – LED lighting, LED drivers, air conditioning and fansNote! The switch-on peak of inductive loads such as LED lighting damages the relays. Use the RC Snubber to absorb this switch-on peak.FeaturesZ-Wave 800110-240VACOutput 2x16A, max 25A totalSwitch connection 2xCurrent measurementProtected against overloadProtected against overheatingProtected against voltage peaks Built-in distribution box, DIN RailManual

Product number: QPSW-0A2P16EU

€103.00*

Shelly Qubino Wave Pro 3

The Shelly Wave Pro 3 is a professional DIN rail module with three individually switchable relay outputs, suitable for residential and commercial Z-Wave installations. Thanks to the Z-Wave 800 chipset, the module supports both mesh networks and Z-Wave Long Range (selectable during inclusion). Each output supports loads up to 16 A (48 A total) and can be operated locally via a connected wall switch or remotely via a Z-Wave gateway. The relays are volt-free and suitable for switching voltages up to 240 V AC or 30 V DC. The module is protected against overcurrent and overheating and includes energy metering per channel, making it suitable for demanding applications such as lighting, heating systems, fans and other electrical devices. Supported load types Resistive (Ohmic) – Incandescent, halogen, heating appliances Capacitive – Electronic equipment with capacitors Inductive (with RC Snubber) – LED lighting, LED drivers, air conditioners and fans Note! The inrush current of inductive loads such as LED lighting may damage the relays. Use an RC Snubber to suppress these inrush currents. Features DIN rail mounting, suitable for standard electrical panels 3x relay output (each up to 16 A resistive, 48 A total) 3x switch input (230 V AC) for local control Volt-free relay contacts Supports Z-Wave mesh and Long Range (selectable during inclusion) Real-time energy metering per channel Protection against overcurrent and overheating Z-Wave 800 chipset (Z-Wave Plus v2) Dimensions: 94 × 19 × 69 mm (3 DIN units wide)

Product number: QUSW-0A3X16EU

€106.00*

Shelly Qubino Wave Pro Shutter

The Shelly Qubino Wave Pro Shutter module is a Z-Wave 800 built-in module (DIN rail) for operating and accurately positioning 240VAC bi-directional motors. Ideal for control from central switch or distribution cabinets. The module supports active energy measurement and is designed for operating motorized curtains, blinds, screens, awnings and other motor-controlled solutions with electronic or mechanical limit switches. It is possible to control the module wirelessly via Z-Wave, as well as using a connected wall switch(es). The module can be powered with a voltage of 110-240VAC. The maximum load capacity per output is a maximum of 16A. It can be operated with single or double wall switches. In addition, the module is equipped with multiple protection functions, including protection against overheating, overvoltage and overcurrent. Features • Z-Wave 800 series • Automatic calibration of endpoints • Blind position support (tilt) • Maximum load capacity: 16A • Protected against overheating • Supports over-the-air firmware updates (OTA) • Can be used with different types of switches

Product number: QPSH-0A1P10EU

€104.00*

Shelly Qubino Wave Shutter

The Shelly Qubino Wave Shutter module is a Z-Wave 800 built-in module for operating and accurately positioning 230VAC bi-directional motors. The module supports active energy measurement and is designed to operate motorized curtains, blinds, screens, awnings and other motor-controlled solutions with electronic or mechanical limit switches. It is possible to control the module wirelessly via Z-Wave, as well as using a connected wall switch(es). The module can be powered with a voltage of 110-240VAC. The maximum load capacity per output is a maximum of 10A. It can be operated with single or double wall switches. In addition, the module is equipped with multiple protection functions, including protection against overheating, overvoltage and overcurrent. Features • Z-Wave 800 series • Automatic calibration of endpoints • Blind position support (tilt) • Maximum load capacity: 10A • Protected against overheating • Supports over-the-air firmware updates (OTA) • Can be used with different types of switches

Product number: QNSW-001P10EU

€38.00*

New

Shelly Wave Dimmer

The Shelly Wave Dimmer is a compact in-wall Z-Wave® dimmer for lighting, compatible with both mesh and Long Range topologies thanks to its Z-Wave 800 chipset. During inclusion, you can select either network type. You can connect 2 switches and control 1 output for dimmable lights up to 150 W (LED) / 200 W (halogen/incandescent). With a Shelly Bypass (sold separately), the Shelly Dimmer also supports 2-wire installations. Key features: Inputs: 2× switch/push-button via screw terminals Outputs: 1× dimmable light output via screw terminals Max load: LED up to 150 W, halogen/incandescent up to 200 W Also suitable for 2-wire installations with Shelly Bypass (sold separately) Network: Z-Wave mesh and Long Range – selectable during inclusion Security: S2 (Authenticated/Unauthenticated), S0, Unsecure Protection: internal protection against overheating (>95 °C), overcurrent (>0.9 A +15%) and overvoltage (>240 V +15%) LED indicator: RGB LED for status and signals (includes LED mode for alarms) OTA updates: supported via gateway

Product number: QLDM-0A101EUL

€51.00*

Shelly Wave Door/Window

The Shelly Wave Door/Window is a sensor designed to accurately detect the opening or closing of doors and windows. The sensor can also measure light intensity and features a tilt function specifically for tilt-and-turn windows to detect if a window is in a tilt or turn position. The Wave Door/Window sensor uses a Z-Wave 800 chipset, making it highly energy-efficient. To use the tilt function, the sensor itself, not the magnet, must be mounted on the movable part. Note! The sensor does not yet have full support on the mentioned platforms. Check the current compatibility via the manual link below. Based on our own tests on the HC3, the open/close detection works well, and Lux also works but only updates upon opening/closing or wake-up. The tilt function does not seem to work. Note that the unit needs to be added in Singlechannel mode (see associations) and corrected. Features Z-Wave 800 chipset S2 security Open/close, Lux, and Tilt detection CR2032 battery Sensor dimensions: 35 x 35 x 7 mm Magnet dimensions: 35 x 12 x 7 mm Indoor use Manual

Product number: QNDW-002CEU

€32.00*

New

Shelly Wave H&T - White

The Shelly Wave H T is a smart Z-Wave® temperature and humidity sensor, featuring S2 security and ultra-low power consumption thanks to its Z-Wave 800 chipset. Supporting both traditional Z-Wave® (mesh) and Z-Wave® Long Range, as well as SmartStart functionality, this device allows you to choose the optimal network type during inclusion based on your installation setup. Ideal for households, offices, educational institutions, and MDUs. Key features: Sensors: Temperature + humidity Security: Z-Wave® Unsecure, S0, S2 Unauthenticated / S2 Authenticated Z-Wave 800 Series (Z-Wave Mesh Network and Z-Wave Long Range Star Network) SmartStart inclusion: Add via QR code within 10 minutes after power-up Battery: CR123A (up to 2 years battery life) OTA updates: Firmware updates possible via gateway

Product number: QLHT-0U2ZEU

€33.00*

New

Shelly Wave Motion

The Shelly Wave Motion is a compact Z-Wave® motion and light sensor, equipped with a PIR sensor and integrated light sensor. This device supports both traditional Z-Wave® mesh networks and Z-Wave® Long Range. During inclusion, you can select the preferred network type depending on coverage and infrastructure. Thanks to S2 security, energy-efficient operation, and easy installation, this sensor is ideal for use in homes, offices, and commercial environments. Upon detecting motion, the sensor sends a Z-Wave® signal including light level and battery status. Key features: Sensors: PIR motion detection + light sensor Security: Z-Wave® S2 (Authenticated/Unauthenticated) Z-Wave 800 Series (Z-Wave Mesh Network and Z-Wave Long Range Star Network) Battery: 1× CR2477 (up to 3 years of battery life) LED indicator: Yes – provides feedback upon detection or interaction Mounting: Wall or ceiling, compact design Burst interval: Sends motion, light, and battery status upon trigger; interval configurable via parameter Compatibility Compatible with all certified Z-Wave® 700/800 hubs and gateways. Tested with Homey, Fibaro HC3, SmartThings, and Home Assistant.

Product number: QLMO-003FEU

€36.00*

New

Shelly Wave Plug S

<div>The Shelly Wave Plug S is a smart Z-Wave® plug with energy monitoring, overheating and overload protection. Easily switch connected devices on or off remotely via app, PC, or gateway. Equipped with the Z-Wave 800 chipset, the plug supports both classic Z-Wave® mesh and Z-Wave® Long Range (star topology) – select your preferred network type during inclusion.</div><div><br></div><div><b>Key features:</b></div><div><ul><li><span style="letter-spacing: 0px;">Type-F Schuko</span></li><li><span style="letter-spacing: 0px;">On/Off switching: via Z-Wave command or S-button</span></li><li><span style="letter-spacing: 0px;">Z-Wave 800 Series (Z-Wave Mesh Network and Z-Wave Long Range Star Network)</span></li><li><span style="letter-spacing: 0px;">Energy monitoring: measures power (W), energy consumption (kWh), voltage, and current</span></li><li><span style="letter-spacing: 0px;">Protection: against overheating, overload, overcurrent, and overvoltage</span></li><li><span style="letter-spacing: 0px;">Associations: direct communication with other Z-Wave devices without gateway</span></li><li><span style="letter-spacing: 0px;">SmartStart: QR code inclusion within 10 min (with S2 security)</span></li><li><span style="letter-spacing: 0px;">Over-the-Air (OTA): firmware updates available via gateway</span></li></ul></div>

Product number: QNPL-0A112EU

€40.00*

Shelly Wave Pro Dimmer 2PM

The Shelly Wave Pro Dimmer 2PM is a DIN-rail-mounted dimmer. The module supports active energy measurement and is designed to dim 2 light sources. The Wave Pro Dimmer 2PM can be operated with 2 switches. The smart dimmer works with Z-Wave, using a Z-Wave 800 chipset, and is compatible with Homey, Home Center 3, and other platforms such as Home Assistant and SmartThings. You can easily install the dimmer in your fuse box on a DIN rail, allowing you to dim 2 light sources with a maximum of 200 watts per channel. Note! The dimmer does not yet have full support on the mentioned platforms. Check the current compatibility via the manual link below.Based on our own tests on the HC3, it seems possible to add the unit after several attempts, resulting in a usable endpoint for both channels. Note that the unit needs to be added in Singlechannel mode (see associations) and corrected. Supported Light Sources Incandescent bulbs Dimmable LED and CFL Dimmable electronic transformers Features 110-240VAC Z-Wave 800 chipset Maximum 200 watts per channel (2 channels) S2 security Trailing edge Power measurement Overload protection Overheat protection Surge protection Fuse box installation, DIN rail 19mm width Manual

Product number: QPDM-0A2P01EU

€96.00*