Shelly Pro Dimmer 1PM

Actors:	Dimmer
Operating humidity:	30% to 70% RH
Operating temperature:	-20°C to 40°C
Power source:	110-240V AC, 50/60Hz
Range:	outdoor up to 50m indoors up to 30m (Depending on terrain and building construction)

New

Shelly Wave Pro Dimmer 1PM

The Shelly Wave Pro Dimmer 1PM is a DIN-rail-mounted dimmer. The module supports active energy measurement and is designed to dim a single light source. The Wave Pro Dimmer 1PM can be operated with 2 switches. The smart dimmer works with Z-Wave, using a Z-Wave 800 chipset, and is compatible with Homey, Home Center 3, and other platforms such as Home Assistant and SmartThings. You can easily install the dimmer in your fuse box on a DIN rail, allowing you to dim one light source with a maximum of 200 watts. Note! The dimmer does not yet have full support on the mentioned platforms. Check the current compatibility via the manual link below. Based on our own tests on the HC3, it seems possible to add the unit after several attempts, resulting in a usable endpoint. Note that the unit needs to be added in Singlechannel mode (see associations) and corrected. Supported Light Sources Incandescent bulbs Dimmable LED and CFL Dimmable electronic transformers Features 110-240VAC Z-Wave 800 chipset S2 security Maximum 200 watts (1 channel) 2 switch contacts Trailing edge Power measurement Overload protection Overheat protection Surge protection Fuse box installation, DIN rail 19mm width Manual

Product number: QPDM-0A1P01EU

€55.90*

Shelly Qubino Wave 1

The Shelly Qubino Wave 1 module is a Z-Wave 800 built-in switch with one potential-free output. The module is designed to control devices such as electric locks, garage doors, entrance gates, irrigation systems, electrical outlets and lighting. With a maximum load capacity of 16A, the module offers sufficient power for various applications. It is possible to control the module wirelessly via Z-Wave, as well as using a wall switch. The module can be powered with a voltage of 110-240V AC, 24-48V DC or 12V DC, providing flexibility in power supply. In addition, the output is potential-free, which means that the input voltage can differ from the device you want to switch. This allows compatibility with various electrical devices. In addition, the module is equipped with protection against overheating. Features Z-Wave 800 series Switch with potential-free output Maximum load capacity: 16A Protected against overheating Supports over-the-air firmware updates (OTA) Use with different types of switches

Product number: QNSW-001X16EU

€23.25*

Shelly Qubino Wave 1 Mini

The Shelly Qubino Wave 1 mini module is a Z-Wave 800 built-in switch with one dry or potential-free contact and one switch. The module is designed to control devices such as gates, garage doors and other electrical appliances. It is possible to control the module wirelessly via Z-Wave, as well as using a single wall switch. The module can be powered with a voltage of 110-240V AC. The potential-free contact has a maximum load capacity at 230v of 8A or 5A at 30V DC.Features Z-Wave 800 series Potential free switchMaximum load capacity at 230V AC - 8A / 30V DC 5ASupports over-the-air firmware updates (OTA) Can be used with different types of switches S2 security and SmartStart suitable Format 29x35x16 mm Wire 0.5 to 1.5 mm²

Product number: QMSW–0A1X8EU

€19.90*

Shelly Qubino Wave 1PM

The Shelly Qubino Wave 1 module is a Z-Wave 800 built-in switch with one potential-free output. The module is designed to control devices such as electric locks, garage doors, entrance gates, irrigation systems, electrical outlets and lighting. With a maximum load capacity of 16A, the module offers sufficient power for various applications. It is possible to control the module wirelessly via Z-Wave, as well as using a wall switch. The module can be powered with a voltage of 110-240V AC, 24-48V DC or 12V DC, providing flexibility in power supply. In addition, the output is potential-free, which means that the input voltage can differ from the device you want to switch. This allows compatibility with various electrical devices. In addition, the module is equipped with protection against overheating. Features Z-Wave 800 series Switch with potential-free output Maximum load capacity: 16A Protected against overheating Supports over-the-air firmware updates (OTA) Use with different types of switches

Product number: QNSW-001P16EU

€24.92*

Shelly Qubino Wave 1PM Mini

The Shelly Qubino Wave 1PM Mini module is a Z-Wave 800 built-in switch with one output and one switch. The module supports active energy metering and is designed to control devices such as lighting, sockets, heaters and other electrical appliances. It is possible to control the module wirelessly via Z-Wave, as well as using a single wall switch. The module can be powered with a voltage of 110-240V AC. The maximum load capacity is 8A. In addition, the module is equipped with multiple protection functions, including protection against overheating, overvoltage and overcurrent. Features Z-Wave 800 series Maximum load capacity at 8A Protected against overheating Supports over-the-air firmware updates (OTA) Can be used with different types of switchesS2 security and SmartStart suitableFormat 29x35x16 mmWire 0.5 to 1.5 mm²

Product number: QMSW–0A1P8EU

€21.90*

Shelly Qubino Wave 2PM

The Shelly Qubino Wave 2PM module is a Z-Wave 800 built-in switch with two outputs. The module supports active energy metering and is designed to control devices such as lighting, fans, infrared panels, heaters and other electrical appliances. It is possible to control the module wirelessly via Z-Wave, as well as using a wall switch. The module can be powered with a voltage of 110-240V AC or 24DC, providing flexibility in the power supply. The maximum load capacity at AC is 16A and at DC it is 10A. The outputs of the Wave 2PM can switch 10A individually and 16A combined. In addition, the module is equipped with multiple protection functions, including protection against overheating, overvoltage and overcurrent. Features Z-Wave 800 series Maximum load capacity at AC: 16A, at DC: 10A Protected against overheating Supports over-the-air firmware updates (OTA) Use with different types of switches

Product number: QNSW-002P16EU

€29.08*

Shelly Qubino Wave i4

This Shelly Qubino Wave i4 is a Z-Wave 800 module suitable for 4 switching contacts and is powered by 230v. The module sends Central Scene commands and/or associations when one of the buttons is used in the following way (see manual for more explanation): Press 1x brieflyPress 2x brieflyPress 1x and holdReleaseFeaturesZ-Wave 800110-240VAC Recessed, behind (wall) switch(es)Works with switch, pulse switch, hotel switchSwitch connection 4xManual

Product number: QNSN-0A24XEU

€14.90*

Shelly Qubino Wave i4DC

This Shelly Qubino Wave i4DC is a Z-Wave 800 module suitable for 4 switching contacts and is powered by 5-24v DC (direct voltage). The module sends Central Scene commands and/or associations when one of the buttons is used in the following way (see manual for more explanation) :Press 1x briefly Press 2x briefly Press once and hold Letting go Features Z-Wave 800 5-24V DCRecessed, behind (wall) switch(es) Works with switch, pulse switch, hotel switch Switch connection 4xManual

Product number: QNSN-0D24XEU

€14.90*

Shelly Qubino Wave PM Mini

The Shelly Qubino Wave PM mini module is a Z-Wave 800 built-in module for current measurement. The module is designed for current measurement of devices such as lighting, sockets, heaters and other electrical appliances. The module can be powered with a voltage of 110-240V AC. The maximum load capacity is 16A. Features Z-Wave 800 series Maximum load capacity 16A Supports over-the-air firmware updates (OTA) S2 security and SmartStart suitableFormat 29x35x16 mmWire 0.5 to 1.5 mm²

Product number: QMEM–0A1PC16EU

€20.90*

Shelly Qubino Wave Pro 1

The Shelly Qubino Wave Pro 1 is a Dinrail mountable Z-Wave 800 actor. The module is designed to operate 1 device such as lighting, fans, infrared panels, heaters and other electrical appliances. It is possible to operate the module wirelessly via Z-Wave, as well as using a (wall) switch. The maximum load capacity is 16A. Supported load types Resistive (Ohms) – Incandescent, halogen, heaters Capacitive – Electronic equipment with capacitors Inductive (with RC Snubber) – LED lighting, LED drivers, air conditioning and fans Attention! The switch-on peak of inductive loads such as LED lighting damages the relays. Use the RC Snubber to absorb this switch-on peak. Features Z-Wave 800 110-240VAC Output 1x16ASwitch connection 2x Protected against overload Protected against overheating Protected against voltage peaks Built-in distribution box, DIN-RailManual

Product number: QPSW-0A1X16EU

€49.50*

Shelly Qubino Wave Pro 1PM

The Shelly Qubino Wave Pro 1PM is a Dinrail mountable Z-Wave 800 actor. The module supports active energy measurement and is designed to control 1 device such as lighting, fans, infrared panels, heaters and other electrical appliances. It is possible to operate the module wirelessly via Z-Wave, as well as using a (wall) switch. The maximum load capacity is 16A. Supported load types Resistive (Ohms) – Incandescent, halogen, heaters Capacitive – Electronic equipment with capacitors Inductive (with RC Snubber) – LED lighting, LED drivers, air conditioning and fans Caution! The switch-on peak of inductive loads such as LED lighting damages the relays. Use the RC Snubber to absorb this switch-on peak. Features Z-Wave 800 110-240VAC Output 1x16ASwitch connection 2xCurrent measurement Protected against overload Protected against overheating Protected against voltage peaks Built-in distribution box, DIN rail Manual

Product number: QPSW-0A1P16EU

€60.50*

Shelly Qubino Wave Pro 2

The Shelly Qubino Wave Pro 2 is a Dinrail mountable Z-Wave 800 actor. The module is designed to control 2 devices such as lighting, fans, infrared panels, heaters and other electrical appliances. It is possible to operate the module wirelessly via Z-Wave, as well as using a (wall) switch. The maximum load capacity is 16A per channel and a combined maximum of 25A. Supported load types Resistive (Ohms) – Incandescent, halogen, heaters Capacitive – Electronic equipment with capacitors Inductive (with RC Snubber) – LED lighting, LED drivers, air conditioning and fans Note! The switch-on peak of inductive loads such as LED lighting damages the relays. Use the RC Snubber to absorb this switch-on peak. FeaturesZ- Wave800 110-240VAC Output 2x16A, max 25A totalSwitch connection 2xProtected against overload Protected against overheating Protected against voltage peaks Built-in distribution box, DIN-RailManual

Product number: QPSW-0A2X16EU

€65.90*

Shelly Qubino Wave Pro 2PM

The Shelly Qubino Wave Pro 2PM is a Dinrail mountable Z-Wave 800 actor. The module supports active energy metering and is designed to control 2 devices such as lighting, fans, infrared panels, heaters and other electrical appliances. It is possible to operate the module wirelessly via Z-Wave, as well as using a (wall) switch.The maximum load capacity is 16A per channel and a combined maximum of 25A.Supported load typesResistive (Ohmic) – Incandescent lamp, halogen, heating appliancesCapacitive – Electronic equipment with capacitorsInductive (with RC Snubber) – LED lighting, LED drivers, air conditioning and fansNote! The switch-on peak of inductive loads such as LED lighting damages the relays. Use the RC Snubber to absorb this switch-on peak.FeaturesZ-Wave 800110-240VACOutput 2x16A, max 25A totalSwitch connection 2xCurrent measurementProtected against overloadProtected against overheatingProtected against voltage peaks Built-in distribution box, DIN RailManual

Product number: QPSW-0A2P16EU

€82.50*

Shelly Qubino Wave Pro 3

The Shelly Qubino Wave Pro 3 is a DIN-Rail module with three (3) switching inputs and outputs. This Z-Wave module with 800 series Z-Wave chip makes it possible to switch three (3) different devices such as lighting, fans, infrared panels, heaters, valves and other electrical devices from a switch or distribution box.It is possible to control the outputs on the module wirelessly via Z -Wave gateway, as well as using a physical (wall) switch connected to the input corresponding to the output on this module.The maximum load capacity is 16A per relay output. The relay outputs are potential-free, can be switched between voltages from 0 to 240VAC (or 0 to 30 VDC) per module.Supported load types Resistive (Ohms) – Incandescent, halogen, heaters Capacitive – Electronic equipment with capacitors Inductive (with RC Snubber) – LED lighting, LED drivers, air conditioning and fans Attention! The switch-on peak of inductive loads such as LED lighting damages the relays. Use the RC Snubber to absorb this switch-on peak. FeaturesZ- Wave800 110-240VAC Output 3x16A, max 48A totalSwitch connection 3xProtected against overload Protected against overheating Protected against voltage peaks Built-in groups/switch cabinet on DIN rail

Product number: QPSW-0A3X16EU

€69.90*

Shelly Qubino Wave Pro Shutter

The Shelly Qubino Wave Pro Shutter module is a Z-Wave 800 built-in module (DIN rail) for operating and accurately positioning 240VAC bi-directional motors. Ideal for control from central switch or distribution cabinets. The module supports active energy measurement and is designed for operating motorized curtains, blinds, screens, awnings and other motor-controlled solutions with electronic or mechanical limit switches. It is possible to control the module wirelessly via Z-Wave, as well as using a connected wall switch(es). The module can be powered with a voltage of 110-240VAC. The maximum load capacity per output is a maximum of 16A. It can be operated with single or double wall switches. In addition, the module is equipped with multiple protection functions, including protection against overheating, overvoltage and overcurrent. Features • Z-Wave 800 series • Automatic calibration of endpoints • Blind position support (tilt) • Maximum load capacity: 16A • Protected against overheating • Supports over-the-air firmware updates (OTA) • Can be used with different types of switches

Product number: QPSH-0A1P10EU

€97.90*

Shelly Qubino Wave Shutter

The Shelly Qubino Wave Shutter module is a Z-Wave 800 built-in module for operating and accurately positioning 230VAC bi-directional motors. The module supports active energy measurement and is designed to operate motorized curtains, blinds, screens, awnings and other motor-controlled solutions with electronic or mechanical limit switches. It is possible to control the module wirelessly via Z-Wave, as well as using a connected wall switch(es). The module can be powered with a voltage of 110-240VAC. The maximum load capacity per output is a maximum of 10A. It can be operated with single or double wall switches. In addition, the module is equipped with multiple protection functions, including protection against overheating, overvoltage and overcurrent. Features • Z-Wave 800 series • Automatic calibration of endpoints • Blind position support (tilt) • Maximum load capacity: 10A • Protected against overheating • Supports over-the-air firmware updates (OTA) • Can be used with different types of switches

Product number: QNSW-001P10EU

€29.08*

New

Shelly Wave Pro Dimmer 2PM

The Shelly Wave Pro Dimmer 2PM is a DIN-rail-mounted dimmer. The module supports active energy measurement and is designed to dim 2 light sources. The Wave Pro Dimmer 2PM can be operated with 2 switches. The smart dimmer works with Z-Wave, using a Z-Wave 800 chipset, and is compatible with Homey, Home Center 3, and other platforms such as Home Assistant and SmartThings. You can easily install the dimmer in your fuse box on a DIN rail, allowing you to dim 2 light sources with a maximum of 200 watts per channel. Note! The dimmer does not yet have full support on the mentioned platforms. Check the current compatibility via the manual link below.Based on our own tests on the HC3, it seems possible to add the unit after several attempts, resulting in a usable endpoint for both channels. Note that the unit needs to be added in Singlechannel mode (see associations) and corrected. Supported Light Sources Incandescent bulbs Dimmable LED and CFL Dimmable electronic transformers Features 110-240VAC Z-Wave 800 chipset Maximum 200 watts per channel (2 channels) S2 security Trailing edge Power measurement Overload protection Overheat protection Surge protection Fuse box installation, DIN rail 19mm width Manual

Product number: QPDM-0A2P01EU

€64.90*